抗磨损性能

Ni的加入一定程度提高了涂层的结合强度和抗磨损性能。

The addition of Ni can also relatively enhance bonding strength and wear properties of coatings .

SiC颗粒增强铝基复合材料切削表面分形维数及其与抗磨损性能的关系

Fractal Surface of the SiC Particle-Reinforced Metal Matrix Composites and its Relationship with Abraison-Resisted Feature

Si3N4基陶瓷&金属摩擦副抗磨损性能的研究

Study on Wear Resistance Behavior of Si_3N_4 Based Ceramic-Matal Friction Pair

WC颗粒增强Cr系抗磨白口铸铁表层复合材料的抗磨损性能研究

Study of Abrasive Wear Resistant of WC Particle Reinforced Chromium White Cast Irons Matrix Composite

结果表明：含Cr、W、Mo的材料硬度高、抗磨损性能好；

The results indicate : materials containing Cr , W , Mo have better hardness and wear resistance property ;

纳米TiB2颗粒增强了Cu基体的抗磨损性能。

It has been found that TiB_2 nanoparticles improved the wear of resistance the in-situ composites .

结果表明：SiO2纳米微粒作为锂基脂添加剂具有良好的抗磨损性能，能够显著提高锂基脂的失效载荷。

Analytical results indicate that SiO_2 nanoparticles as additive can increase antiwear ability and load-carrying capacity of lithium grease .

磨损实验结果表明，镀层的抗磨损性能与其本身的物化性质有关，Al2O3镀层的抗磨损性最好。

The wear resistance test indicates , of three coatings , that of the Al_ ( 2 ) O_ ( 3 ) coatings is the best one due to its nature characteristics .

结果表明，含有10%镍基合金粉的WC-Co涂层具有较好的抗磨损性能。

The result showed that the WC - 12 % Co coating with 10 % nickel alloy powder presents better wear resistance .

一种Ni-PTFE非电复合镀层的制备工艺及抗磨损性能研究

Research on Anti-wear Property of Ni-PTFE Electroless Composite Plating Layer

结果表明，在实验条件下，纳米TiO2/PTFE复合材料的抗磨粒磨损性能，以纳米TiO2质量分数为2%时，填充PTFE复合材料抗磨损性能最好。

The results showed that the abrasive resistance of TiO_2 / PTFE composite was the best when the mass fraction of nano - meter TiO_2 was about 2 % in the test .

CNG／汽油两用燃料发动机油比SF级汽油机油具有更好的清净分散性能、抗磨损性能和高温抗氧化性能；

CNG / gasoline convertible-fuel engine oil has better performance than that of gasoline engine oil of the SF level , good performance of detergent dispersant , high-temperature anti-oxidation and abrasion .

通过销盘磨损试验，研究了在两体磨损条件下，WC颗粒增强抗磨白口铸铁表层复合材料的抗磨损性能；并与相应的抗磨白口铸铁的抗磨损性能进行了比较。

Wear-resistant performance of WC particle reinforced chromium white cast iron matrix composite was studied under the condition of two body wear by pin-on-disk test , and the wear-resistant performance is compared with white cast iron .

Al2O3颗粒可以大幅度提高Cu基体材料的抗磨损性能，且Al2O3含量多（10%、15%）的比含量少（5%）的复合材料抗磨损性更好；

The introduction of Al2O3 particles can largely enhance the abrasion resistance of Cu matrix materials . Larger amount of Al2O3 particles such as ten percent and fifteen percent can bring better abrasion resistance of composites compared to lower amount of five percent .

结果表明：与TiN薄膜相比，Ti-B-N薄膜抗磨损性能有显著提高，磨损机制与TiN薄膜不同，摩擦系数较TiN稍高。

The wear resistances of Ti-B-N coatings remarkably increase with a certain addition of boron , which caused the change of friction mechanism of TiN coatings , although its friction coefficient is higher than that of TiN .

Al-Mo-Si共渗的抗磨损性能提高了8.38倍；

Al-Mo-Si multi-element penetration has been improved by 8.38 times ;

镀层与45钢常温对磨时，随着Ti含量的增加，其摩擦系数从0.52降至0.37，磨损失重率也逐渐降低，镀层的抗磨损性能增加，磨损机制由粘着磨损向磨粒磨损转换。

Friction and wear at room temperature , with the increase of Ti content , the friction coefficients with 45 steel take from 0.5 to 0.37 , wear rates of the coatings also decrease , and the wear mechanism undergoes a adhesive wear → abrasive wear transformation .

100h试验后结果表明：1号涂层的抗磨损性能要优于2号；

After 100 hours , the experimental results show that the wearing quality of number one coating is better than that of number two coating ;

VIM-VAR52100是含碳量含铬量高的合金钢，能被深度硬化，具有高抗磨损性能。

VIM-VAR52100 is a high-carbon , chromium-bearing alloy steel possessing deep hardening characteristics as well as high wear resistance .

反应600h后卸载下的催化剂的形貌观测表明，催化剂的磨损主要是由化学磨损引起的，提高焙烧温度可明显改善其抗磨损性能，焙烧温度高于400℃时，催化剂具有较好的抗磨损性能。

The attrition of the catalyst was mainly due to the chemical attrition . The morphology observation of the catalyst after FTS run for 600 h showed that the attrition resistance was enhanced by increasing the calcination temperature , and the catalyst calcined above 400 ℃ exhibited robust attrition resistance .

Ni-Co/纳米金刚石复合镀层抗磨损性能的研究

Study on the Anti-wear Behavior of Ni-Co / Diamond Nanocomposite Coatings

龋病人牙釉质表面硬度及抗磨损性能测试

Test of Hardness and Wear Resistance of Artificial Carious Human Enamel

液晶润滑添加剂的抗磨损性能研究

Study on the Anti-wear Properties of Liquid Crystal Lubricating Additives

此外，还要具有足够的抗磨损性能。

Furthermore , adequate resistance to abrasion shall be guaranteed .

高档汽油机油抗磨损性能试验方法研究

Research of Wear Resistance Test Method of High Grade Gasoline Engine Oils

工业齿轮油抗磨损性能的区分性考察

Distinctiveness Investigation of Anti-wear Property for Industrial Gear Oils

本文研究了SYNTH&8添加剂的抗磨损性能，并对其作用机理作了分析。

The article studies the antiwear properties of SYNTH-8 additive and investigate its mechanism .

具有足够的抗磨损性能。

E resistance to abrasion shall be guaranteed .

过去曾设法用化学变性方法，提高纤维的抗磨损性能。

There have been attempts to modify the fiber chemically to resist abrasion enhancement .

SYNTH&8添加剂抗磨损性能的研究

Study on Antiwear Properties of SYNTH-8 Additive