成形加工

45钢制薄法兰盘毂类零件的近净成形加工技术

A Finish-approaching Forming Technology for Thin Flange , Rim Type Components Made of 45 Steel

汽车差速器锥齿轮的温锻制坯/冷摆辗成形加工技术研究

Research on Warm Forging / Cold Orbital Forming Technology for the Straight Bevel Gear in Differential Case

仿生支架可以采用CAD建模方法设计内部结构，并采用快速成形加工制备仿生支架实体。

Such porous scaffolds can be designed by CAD modeling method , and fabricated by rap - id prototyping technology .

刚性模胀压成形加工是一种重要的高效U形金属波纹管成形方法。

The inflationary pressure forming processing of rigid mould is an important efficient U-shaped metal bellows processing method .

基于PMAC的电火花成形加工机床控制系统研究

Study on PMAC-Based Control System for Electro-discharge Machining Tool

结果表明，Ti－15－3合金件热成形加工时，在等强温度附近经过较大程度的变形可以得到晶粒细小的均匀组织。

The result shows , the uniform microstructure with fine grains can be attained by deforming near equal strength temperature strongly during heat forming Ti 15 3 alloy parts .

运用所开发的加工条件，对薄镍板Meso尺度零件进行成形加工，可满足相关设计要求。

In the end , the meso-scale parts were manufactured using the developed conditions , which could satisfy the design requirements .

聚碳酸酯（Polycarbonate）是一种综合性能优良的热塑性工程塑料，其制品具有良好的透光性、抗冲击性能和成形加工性能，已经应用到社会的各个领域。

Polycarbonate is a comprehensive engineering thermoplastics with excellent performance , good transparency , impact resistance and molding properties Polycarbonate products have been applied to all areas of society .

通过动态流变测试可知，添加少量的SiO2降低了体系的储能模量和粘度，有利于成形加工；而随着SiO2含量的增加，复合体系的储能模量、损耗模量和粘度都大幅度升高。

Dynamical rheology results showed a decrease of the storage modulus and viscosity of composites with low SiO2 content , but the storage modulus and viscosity increased sharply with the increasing of SiO2 content .

分别用管状圆柱电极和削边电极在通用电火花成形加工机床上成功地加工出直径为2mm、深径比大于20、锥度小于0.5%的深小孔。

The hole of which the diameter is 2 mm , the depth / diameter ratio is more than 20 and the taper is less than 0.5 % can be machined successfully on the general sink EDM machine tool by using the tube column electrode or the tube flatted electrode .

本文从Cu-Ni-Sn合金系着手进行研究，成功地开发出了与黄铜基本相同的工艺，能够制造强度、弹性、耐应力松弛特性、成形加工性及溃透性等优良的铜合金NB-109。

In this paper , the Cu-Ni-Sn alloy parts have been investigated and success has been made in making copper alloy NB-109 of high intensity , elasticity , stress resistance , process and permeability , which has almost the same process as the copper .

金属板材数控渐进成形加工轨迹交互修改及优化

Machining Tool-Path Interactive Modification and Optimization of Sheet Metal Incremental Forming

激光快速成形加工中扫描方式与成形精度的研究与实验

The study of scanning path and part accuracy in rapid prototyping

电火花成形加工机的小件与精密模具加工

Small Parts and Precision Mould & Die Machining on EDM

内螺旋翅片铜管充液旋压成形加工的研究

Study on the Oil Filled Spinning of Copper Inner Spiral Fin Tubes

点接触内啮合直齿锥齿轮全成形加工原理

Principle of complete form machining of point contact internal straight-tooth bevel gear

卷绕成形加工专用机床的设计

Design of the Special-purpose Machine Tool for Rolling Shaping Process

汽车方向机联结环的冷摆辗成形加工技术研究

Study on Cold Rotary Forging Technology of Joint with Teeth in Automobile

数控技术在电火花成形加工中的应用现状和发展趋势

Application State and Developing Trend of Electric Spark Forming with NC Technique

锻造是一种主要的材料成形加工方法。

Forging is one of primary material forming processes .

激光三维铣削在陶瓷成形加工中的应用研究

The application of 3D laser milling for ceramic materials

激光快速成形加工中烧结中心轨迹的研究

A Study on the Orbit of the Sintering Center in Selective Laser Sintering

板材数字化成形加工路径规划研究

Process route planning research of sheet metal digital forming

多曲率油槽电火花成形加工及精密组合电极的设计

EDM of Oil Supply Tank with Multi-curvature and Design of Accurate Assembly Electrode

电火花成形加工工作液应用工艺特性试验

Test of working characteristics of dielectric fluid in EDM

基于网络的工程材料与成形加工基础虚拟实验室

Web-based Virtual Laboratory in Engineering Materials and Formed Machining

金属基复合材料成形加工研究进展

Progress of research forming of metal matrix composites

电火花成形加工机床中的模糊逻辑控制

Fuzzy Logic Control in EDM Die - sinking

金属板材无模成形加工轨迹生成的研究

Tool Path Generation for Sheet Metal Dieless Forming

在部分双卡簧片折弯处发现有尖锐凹角并有明显微裂纹，裂纹表面有镍和铜，说明裂纹是在成形加工过程中形成。

Nickel and copper elemens on crack surface showed crack formation during forming process .