应力分析

yìnɡ lì fēn xī
  • stress analysis
应力分析应力分析
  1. 织构材料X射线应力分析的线性方程组

    Simultaneous Linear Equations of X ray Stress Analysis for Textured Materials

  2. 复杂弧面凸轮曲率和应力分析及其CAD

    Curvature and Contact Stress Analysis of Complex Globoid Cam Mechanism

  3. 由于许多不确定的因素通常不能进行正确的应力分析。

    Because of many uncertainties , an exact analysis of the stresses usually cannot be made .

  4. 利用ANSYS软件对三叉杆滑块式万向联轴器进行应力分析

    Stress Analysis of a Tripod Sliding Universal Joint with ANSYS Software

  5. 分析结果表明,二维总应力分析方法定性上能较为合理地给出坝体地震反应情况,Seed简化法直接用于坝体液化分析存在着一些问题,需要进一步改进。

    Comparison shows that program QUAD-4 provides a better analysis qualitatively and the Seed 's method needs to improve for analyzing seismic responses of dam .

  6. 通过进行ADAMS与ANSYS之间的双向数据交换,对该喷管弹性机构构件进行了动态应力分析。

    Through bidirectional data interchange between ADAMS and ANSYS , dynamic stress analysis of this elastic mechanism is conducted .

  7. 应力分析表明在同一溅射时间,随着氩气压强的减小,Al膜厚度增大,在相同选区范围内,Al膜的应力差变小,应力分布趋于均匀。

    The results of stress analysis show that for the same sputtering time , the stress difference of Al films becomes smaller and the stress distribution becomes more uniform with decreasing Ar pressure and increasing thickness of Al film .

  8. 采用考虑等效龄期的混凝土弹性模量和抗拉强度CEB-FIP1990计算公式来表征早龄期时温度变化对其力学性能的影响,在应力分析中采用Bazant的双幂函数徐变模型。

    The temperature field and thermal stress of concrete wall is calculated by the FEM at early age .

  9. 同时本文运用全塑性应力分析,给出了修补后试件裂纹启裂时的材料动态断裂韧性CTOD的实验结果。

    Simultaneously the experimental results of dynamic fracture toughness CTOD of the patched specimen in the crack initial propagation are given using the fully plastic stress analysis .

  10. SL-2(7)型套管头结构应力分析

    Structural Stress Analysis of SL 2 ( 7 ) Casing Pipe head

  11. 作者对Harrington棒加Edwards套棒(HRS)和C型Harington棒(HRC)两种改良型Harrington棒进行应力分析,确定出棒体的危险截面和危险点。

    We analyzed the stress state of Harrington rod with Edwards sleeve ( HRS ) and Harrington rod of C type ( HRC ), and determined its dangerous cross section and dangerous point .

  12. 在上述闸门有限元应力分析的基础上,应用概率断裂力学建立了裂纹的极限状态方程,并用JC法求出裂纹的失效概率,以此对闸门焊接缺陷的可靠度作出安全评估。

    On the basis of the finite element stress analysis of the gate , the paper establishes the limit state equations of cracks by probability rupture mechanics , and obtains the failure probability of the cracks . Finally , the failure probability of the cracks is elementary estimated .

  13. Ce-Y-Mg复合稳定TZP韧性好,较其它TZP高,有可能成为牙科桩钉材料。不同牙桩修复材料的三维有限元应力分析

    As a result , the TZP stabilized by mult-component stabilizer of CeO 2 / Y 2O 3 / MgO is more likely suitable for the dental post application . Three dimensional finite element stress analysis on different dental post materials

  14. 并以1000m3的大型液化汽球罐为例,运用该软件与商业有限元软件ANSYS7.0,对其进行了参数化设计和有限元应力分析。

    It makes a perfect link with commercial finite element software ANSYS . As an example , a 1000m ~ 3 spherical tank is carried out by parameterized design and finite element stress analysis to show the application of this software .

  15. 反应釜局部结构的有限元应力分析

    Stress Analysis of Part of Reaction Vessel with Finite Element Program

  16. 直接记录散斑法在实验应力分析中的应用

    Application of Laser Speckle Method by Direct Recording in Experimental Mechanics

  17. 油井钻机的相关结构的应力分析和设计。

    Stress analyze and Design Oil rig structure & mechanical components .

  18. U型膨胀节热应力分析及疲劳寿命估算

    Thermal stress analysis and estimated fatigue life of U-type expansion joint

  19. 层合机敏结构的变形传递和层间应力分析

    Analyses of Interlayer Stresses and Strain Transfer in Smart Laminated Structures

  20. 齿轮模型的建立及齿根应力分析

    The Establishment of Gear Model and Analysis of Gear Base Stress

  21. 加氢反应器接管补强部位的应力分析

    Stress Analysis of the Reinforcing Part for Nozzle of Hydrogenation Reactors

  22. 抛物线零件充液拉深成形应力分析

    Stress analysis of the parabola part with hydraulic counter pressure deep-drawing

  23. 飞行器热结构细节应力分析与设计技术研究

    Analysis and design technologies of detail stress of aircraft heat structure

  24. 矿井提升机主轴应力分析

    The Stress Analysis of the Main Shaft of a Mine Hoist

  25. 超大型间接空冷结构体系温度应力分析研究

    Ultra-large Indirect Air-cooled Structure System Temperature Stress Analysis and Study

  26. 单级功率因数校正电路及其开关应力分析

    Single-Stage Power Factor Correction Circuit and Its Switch Stress Analysis

  27. 偏心及同心异径管的三维有限元应力分析

    Stress analyses of eccentric and concentric reducers by tridimensional finite element method

  28. 巨型变压器油箱的光弹性实验应力分析

    Photoelasticity experimental stress analysis of a giant oil tank of a transformer

  29. 连杆螺栓的应力分析与疲劳寿命研究

    Stress Analysis and Fatigue Life Research for Connecting Rod Bolt

  30. 导汽管弯头的应力分析及蠕变寿命计算

    Stress analysis and calculation of creep rupture life of steam lead elbow