固化时间

六种沙生灌木pH值、缓冲容量及对脲醛树脂胶（UF）固化时间的影响

PH Value and Buffering Capacity of 6 Shrub Species and Relevant Effects on Curing Time of UF Resin

红锥木材性质与UF胶固化时间关系的研究

Studies on the Relationship between Castanopsis hystrix Wood Properties and Curing Time of UF

脲醛树酯胶固化时间随3种灌木材的pH值和减缓冲容量的增加而增长。

The setting time of UF increases with the increase of wood pH and alkali buffering capacity .

三种杨木的pH值、缓冲容量及其对脲醛树脂胶固化时间的影响

The pH data buffer capacity of three poplar and their effects on the setting time of UF resin

在pH值相近的情况下，木粉与胶的混合物固化时间随木材缓冲性能的增加而缩短；

Under the condition of having similar pH value , gel-time of mixture of UF resin with wood flour decreased as buffer capacity of the wood flour increased ;

采用远红外（FIR）烘烤方式可使水溶性涂料的固化时间缩短至5分钟以下，且涂膜的综合性能优良。

The solidified time of water soluble resin paints baked by far infrared ( FIR ) is reduced to less than 5 minutes , with their overall properitiess being excellent .

通过试验，提出改进单组份RTV型氯丁橡胶胶粘剂固化时间的途径。

The measure of developing the setting up time of one pack RTV CR adhesive was taken by the test .

其固化时间达到10s左右。

Its cured time reaches to 10 s.

为了合理开发我国西北地区的沙生灌木，研究了内蒙西部地区沙柳、柠条、沙棘、红柳、桦棒、杨柴6种主要沙生灌木的pH值、酸碱缓冲容量与UF胶混合物固化时间。

In order to use shrub materials to produce wood based panels reasonably , pH value , buffering capacity and curing time of 6 main shrub species in the north western China were measured .

根据红外分析确定了理论固化时间，考虑到施工时的实际情况，确定固化时间为48h。

It is determined the theory solidification time according to the infrared analysis , considers the construction the actual situation , the determination solidification time is 48h .

目的检测不同粉体粒径对碳酸化羟基磷灰石水泥（carbonatedhydroxyapatitecement，CHC）的固化时间和压缩强度的影响，为其修复骨缺损提供理论基础。

Objective To investigate the effect of different diameter powder on setting time and compressive stress of carbonated hydroxyapatite cement ( CHC ) .

通过光纤光栅波长偏移与温度和固化时间之间的关系测试，得到了树脂固化过程中残余应变的变化历程，成功实现了RTM工艺树脂固化过程中残余应变的在线监测。

The real time monitoring for residual strain induced by resin cure during the RTM process was realized by measuring the relationship among wave deflection , temperature and curing time .

采用该树脂制备固定化酶的最优条件是：酶质量浓度6mg/mL、温度25℃、固化时间12h。

The optimal process of preparation of immobilization of D-hydantoinase was as follows : mass concentration of cells was 6 mg / mL at 25 ℃ and was solidified for 12 h.

本文介绍了以BMC材料注射汽车前大灯反光罩的成型工艺，并确定了注射成型时的温度、压力、固化时间等工艺参数。

This paper introduces the injection molding process of BMC used in car forehead reflection lampshade , And injection parameters such as injection temperature , injection pressure and cure time are determined .

研究了PAE用量、热固化时间和温度对麻浆、桑皮浆和针叶木化学浆手抄薄型纸湿强度特性的影响。

The wet-strength properties of three thin handsheets made of hemp pulp , softwood pulp and mulberry pulp with the wet-strength resin ( PAE ) as the additive were studied .

啶虫脒/脲醛树脂微胶囊制备的最佳工艺条件为：尿素与甲醛摩尔比例1：1.8，乳化时间1h，酸化时间1h，固化时间2h。

The optimum preparation conditions of acetamiprid / urea-formaldehyde resin microcapsules are : the molar ratio of urea and formaldehyde is 1:1.8 , emulsifying time 1 h , acidification time 1 h , and curing time 2 h.2 .

FRW阻燃木材及未处理材的漆膜附着力、光泽和固化时间的测试结果表明，FRW处理对木材的涂饰性能基本无影响。

Theadhesive force of paint coating , gloss and solidification time of FRW treated wood and untreated woodindicate that the treatment with FRW hardly influences the painting properties of wood .

研究表明MPC的引入不仅明显缩短了浆体的固化时间，且显著改善了抗溃散性；通过调节MPC在浆体中的比例可调控体系的各项理化性能参数。

It was found that MPC not only shortened the setting time but also significantly improved the anti-washout of the paste . The physical and chemical properties of the fa-ICPC could be regulated by adjusting the ratio of MPC to CPC .

以自制MQ硅树脂改善加成型室温硫化硅橡胶的性能，结果表明，MQ硅树脂可以增大加成型室温硫化硅橡胶的交联度，延长其固化时间，有效地改善其力学性能；

Self-made MQ silicone resin was used to improve the properties of addition-cured ambient vulcanization silicone rubber . With the increasing of the MQ silicone resin , the crosslinkage of the silicone rubber was enhanced , setting time was prolonged and mechanical properties were improved .

首先，采用SPI法和差示扫描量热法（DSC）研究了引发剂、低收缩树脂（LPA）对凝胶时间、固化时间、放热峰温度的影响，并从动力学角度分析了固化反应特性。

Firstly , the effects of initiators and LPA on the gel time , curing time and peak temperatures in the curing reaction of UPR were studied by SPI method and differential scanning calorimetry ( DSC ), and the curing characteristics were analyzed in kinetics angle .

ZSL与DCPD两种改性剂同时引入树脂中，协同作用使树脂的力学性能十分优越，且树脂的固化时间、粘度、气干性、耐腐蚀性能均十分突出。

In order to develop a resin fitting to glue for construction , ZSL and DCPD were introduced into resin simultaneity . The modified resin has excellent property of mechanics , curing time , dynamic viscosity , air dry and corrosion resistance .

研究了凝胶注模成型的各种工艺因素对Al2O3-SiC复相陶瓷悬浮体的黏度和固化时间的影响。

The influence of different technological factors of gel casting ( PH , deflocculant , solid content , forming temperature , initiator and catalyst ) on viscosity and gelling time of Al2O3-SiC ceramic suspension is studied in this paper .

方法：（1）制备三种n-HA含量（40wt%、50wt%、60wt%，重量比）的可注射性n-HA/PA66复合骨水泥，对其固化时间、压缩强度、抗稀散性及残余百分比进行测定。

Methods : ( 1 ) Making three kinds of Injectable n-HA / PA66 composite cement , the weight ratio of n-HA in cement were about 40wt % , 50wt % , 60wt % . The setting time , compressive strength , anti-washout and remnant percentage were examined .

结果表明，当总NCO/OH摩尔比为1.4，BDO的量为14%、TMP的量为4%，固化时间为10h，该胶粘剂对APET包装膜粘结性能好。

The experimental results showed that the adhesive has good adhesive power for APET packaging films when the total mole ratio of NCO / OH is 1.4 , the amount of BDO is 14 % , the TMP is 4 % , the curing time is 10h .

研究了固化时间、扩链剂用量、ATPEG分子量和固化剂对该交联弹性体力学及溶胀性能的影响。

The effect of the curing time , the chain-extender ratio , the ATPEG molecular weight as well as the curring agent on the mechanical properties and the swelling ratio was investigated in details .

鳗骨油微胶囊质量特性及固化时间对其的影响

On Qualitative Characters of Microcapsule of Bone Oil From Eels

抗菌性组织调整材料的抗菌效果和固化时间

Study on gelation time and antibacterial effect of antibiotic tissue conditioner material

如果材料或基材温度较高，起沫及固化时间会变长；

Higher material or substrate temperature will increase rise and cure times ;

同时胶粘剂的固化时间和温度存在等效性关系。

The time-temperature equivalence of the adhesive is confirmed .

所需要的固化时间与温度、管道直径和应用压力有关。

Required cure time depends on temperature , pipe diameter , and pressure application .