卡环

安装制动助力器导线和卡环。

Fit the lead for the brake booster and the snap ring .

确定仍可继续使用的厚度最大的卡环。

Determine the thickest snap ring which can still just be used .

液压卡环式步进提升机PLC控制系统设计

Design of PLC Control System for Hydraulic Pressure Clip Ring Step-by-tep Hoist

锯齿状缺口物体边缘V形或锯齿形的缺口附着体义齿与卡环可摘局部义齿咀嚼效率研究

A notch or jagged cut in an edge . Comparative study of masticatory efficiency between attachment dentures and clasp removable partial dentures

Ni-Ti形状记忆合金骨卡环热成形模具设计

Hot Forming Mould Desing for Keeper of Ni-Ti Memory Alloy

RPA卡环支持组织的三维有限元分析

The 3-Dimensional Finite Element Stress Analysis of the Supporting Tissues in the RPA Clasp

树脂卡环对牙面的磨损程度小于Co-Cr卡环。

The abrasion of resin clasp on the tooth surface is less than the Co-Cr clasp .

RPI卡环受力分析与临床应用

Analysis and clinical application of the forced RPI retainer

不同加载条件下RPI卡环固位可摘局部义齿的三维有限元分析

Three Dimensional Finite Element Analysis of RPI Removable Partial Denture under Different Loading Directions

可摘局部义齿改良RPI卡环固位力测试

Retentive force of modified RPI clasp

RPI卡环的改良设计

The Modified RPI Clasp Design

描述了改良RPI卡环的设计，并与传统RPI卡环相比较。

The modified RPI clasp was described and compared with the conventional RPI clasp in the article .

目的研究RPA卡环在游离端义齿应用中支持组织的应力分布状况。

Objective To study the stres distribution of the supporting tissues of the RPA clasp applied in the free end removable partial dentures .

目的：分析RPI卡环固位可摘局部义齿在垂直、水平和斜向加载条件下义齿的基牙及基托下支持组织的应力分布情况。

Objective : To evaluate the stress distribution of RPI removable partial denture under the vertical load , horizontal load and oblique load .

改良RPI卡环的I杆固位尖端只需进入基牙颊面最远中的较小倒凹则可获得足够的固位，而且更美观。

The modified RPI clasp could provide adequate retention with the minimum undercut of the most distal part of abutment tooth and gain good esthetical effect .

Twin-Flex美观卡环在可摘局部义齿中的临床应用

Clinical application of Twin-Flex clasp in removable partial dentures

【结果】颊侧短固位臂-远中邻面板硬固位体的固位力（84±14）N与Aker卡环的固位力（95±10）N无显著性差异。

Result No statically significant difference was revealed between retentive force of short buccal retentive arm distal guiding plate hard retainer ( 8 4 ± 1 4 ) N and that of Akers clasp ( 9 5 ± 1 0 ) N.

结果①剩余牙槽嵴以及末端基牙颊舌侧牙槽嵴顶的吸收：RPA组低于RPI组和传统三臂卡环组；

Results One year after rehabilitation , the bucco lingual alveoli bone loss and the resorption of the residual ridge for the RPA group were lower than those for the RPI and RPC groups .

椎环、弹簧、弹簧座以及卡环，辅助密封圈有“O”形橡胶圈和PTFE楔形环，静环材料都为石墨（M106K）。

Vertebral ring , spring , spring seat and clasp , auxiliary seals have " O " shaped rubber ring and PTFE wedge ring , quiet ring for graphite materials ( M106K ) .

目前关于附着体义齿用于游离端缺牙的研究，主要集中于针对某一类病例或缺失情况的义齿设计及临床效果评价，以及附着体与传统RPI卡环固位体修复的效果对比。

Most of the existing researches about attachment-retained distal-extension RPD are focused on the effect of denture design and clinical effects for a certain kind of edentulous situation , and evaluation among different retention style .

【方法】采用人离体下颌骨作为模型，在垂直脱位力作用下，测试颊侧短固位臂-远中邻面板硬固位体的固位力，并与Aker卡环比较。

Methods This study tested the retentive force of short buccal retentive arm distal guiding plate hard retainer under vertical dislodging force on a human mandible , and compared it with that of Akers clasp .

确保有卡环并且可靠入位。

Make sure that the circlip is present and seated securely .

不同类型卡环对基牙受力影响的光弹应力分析

Photoelastic Stress Analysis of the Effect of Various Clasps on Abutment Tooth

拆卸卡环并使用支承环取下粘性离合器。

Remove snap ring and take out viscous clutch with supporting ring .

卡环嵌入式接口虚拟线切割工艺研究

Virtual Process Technology on Wire Incision to Embed Type Cut of Ring

复合材料壳体与喷管卡环连接结构分析

Stress analysis of check ring connecting structure between composite case and nozzle

小波变换在卡环图像边缘检测中的应用研究

Application and Research on Snap Ring Image Edge Detection Using Wavelet Transformation

拆解工具现在必须推入卡环内。

Disassembly tool must now be pushed into the circlip .

确保卡环和凹面垫圈正确就位。

Ensure that the snap ring and concave washer are seated correctly .

按下卡环，松开燃油管路。

Release the fuel line by pressing in the circlip .