冷却系统

得先把超导冷却系统接好

I got to get this superconducting coolant system back online

闭路循环气冷反应堆反应堆一次冷却系统

Closed cycle gas cooled reactor primary reactor coolant system

紧急冷却系统有可能失灵，核反应堆有可能发生堆芯熔毁。

Emergency cooling systems could fail and a reactor meltdown could occur .

燃油和冷却系统是造成故障的最常见的原因，这一点不奇怪。

It didn 't come as a shock to learn that the fuel and cooling systems are the most common causes of breakdown

当这些计算机处理信息时,会产生大量的热量,因此它们需要巨大的冷却系统。

As these computers deal with information , they produce lots of heat , so they need huge cooling systems .

基于模糊C聚类的油封冷却系统鲁棒辨识研究

Research on the robust Identification based on the fuzzy C-Clustering algorithm for oil seal system

H型钢轧制过程中冷却系统的优化方案

Optimization project of cooling system of H-beam in rolling process

H型钢冷却系统优化

Optimization Project of Cooling of H - beam

CO2回收冷却系统的改进

Improvement of CO_2 Recycling and Cooling System

PET中回旋加速器水冷却系统的研制

The development of water-cooling system for PET cyclotron

SomatomPlus全身CT机架冷却系统驱动电路维修和改进

Repairing and Reform of the Drive Circuit of Cooling System of Somatom Plus CT

注射模冷却系统的CAE技术应用

Application of Cooling System CAE of Injecting Mould

船用柴油机冷却系统防腐CH乳化油性能

Anticorrosive behaviour of CH emulsible oil used in cooling system of shipboard diesel engines

APF型发动机电子控制冷却系统

APF Type Electronically Controlled Engine Cooling System

Ni-Ti形状记忆合金在装甲车辆冷却系统上的应用

The Application of Ni-Ti Shape Memory Alloy to the Cooling System of Armored Vehicles

几年的运行实践证明，密闭式循环水冷却系统可有效地散发SVC装置所产生的热量，保证装置的正常运行。

The performance of the system proved that the full-closed circulating water-cooling system can provide a well heat-dissipating condition for the SVC .

DF（8CJ）型交流传动内燃机车干式冷却系统研制

Research on Dry-cooling System for DF_ ( 8CJ ) AC Freight Diesel Locomotive

为阅读DTC并获得冷却系统资料，详情请参阅单元25，排放控制系统。

To read DTC 's and to obtain cooling system data , refer to Group 25 , Emission Control Systems for proper procedures .

屯兰矿35kV变电站变压器冷却系统的改造

Improvement on the main transformer cooling system in 35 kV substation

42V电控发动机冷却系统的研究

Research of 42V Electronic Control Cooling System in Engine

300～600MW空冷汽轮机组冷却系统的可行性分析

Feasibility Analysis of Cooling System of 300MW ~ 600MW Air Cooled Steam Turbine

AC-600安全壳冷却系统水力特性研究

Studies of the hydrodynamic properties for containment cooling system in AC-600

利用ANSYS有限元分析软件，对用于热轧板带层流冷却系统的U形集管和用于中厚板层流冷却系统的直集管的流场进行了三维稳态数值模拟，得到了管内流体的流动特性。

The 3-dimensional simulation of flow field in both U-shape and straight pipe nozzles of the laminar cooling system for hot strip and plate rolling mill was carried out by ANSYS FEM software respectively , and the fluid flow characteristics were obtained .

研制的4m×8m×4m油槽循环冷却系统，采用全风冷循环冷却系统代替常规的水冷循环冷却系统。

In the circulating cooling system of 4m × 8m × 4m oil tank , circulating full air cooling system has been used instead of conventional circulating water cooling system .

含有不凝性气体的蒸汽冷凝是先进反应堆非能动安全壳冷却系统（PCCS）中重要的换热方式，是当前核反应堆热工水力学研究的一个热点。

Condensation of steam in the presence of noncondensable gases is an important heat transfer mode in the passive containment cooling system ( PCCS ) .

在彩电前壳气辅模具设计中，应用注塑CAE技术对模具气道布置、冷却系统以及熔体充填形态、翘曲状况进行模拟分析，并优化了塑件壁厚。

During the gas-assisted mold design of color TV front shell , using injection CAE technology to simulate and analyze mold gas path layout / location , cooling system and melting filling shape , as well as warp status , the plastic parts wall thickness are optimized .

本文对安全壳进行长期效应的分析结果表明，AC600非能动安全壳冷却系统能够保证安全壳的完整性。

This paper gets the conclusion that the PCCS can ensure the integrality of the AC600 containment in the long-term .

阐述了注塑模（Moldflow）技术在塑料制品（碗厨上盖）注射成型冷却系统中的应用，进行模拟分析，并根据冷却分析的结果提出了相应的优化方案，最终获得了良好的冷却效果。

The CAE ( Moldflow ) technology is carried out to simulate and to analyze the cooling system of the plastic-a kitchen upper cover , and get the good cooling result based on improving .

接着又用MPI/COOL对汽车门板和洗衣机的下平衡环冷却系统进行了优化分析，使得平衡环的冷却效率提高了21.4%，汽车门板的生产周期比其它同类产品少20s。

Then the automobile door panel and the balance ring cooling system of the washing machine is applied with optimize analysis by MPI / COOL . The cooling effect of balance ring is improved by 21.4 % , and the production cycle is less than others by 20s .

以莱芜钢铁公司1500mm热连轧机层流冷却系统为对象，对如何提高带钢卷取温度控制质量进行了研究。

Taking the laminar cooling system of 1 500 mm hot strip rolling mill in Laiwu Iron and Steel Co as an object , how to improve strip temperature control quality is studied .