入口温度

当溶液入口温度达到90℃时，其COP值达到0.83，比传统吸收式制冷系统的COP值高22%。

When the inlet temperature is 90 ℃, the COP can reach 0.83 , which is higher than that of a conventional absorption chiller by 22 % .

另外利用CFD软件FLUENT对涡流管内部的温度场、速度场和压力场进行了二维的数值模拟，并讨论了入口温度、入口压力对涡流管能量分离效应的影响。

In addition , The 2D temperature field , velocity field and pressure field were simulated by Fluent software , and the effect of inlet temperature and inlet pressure were studied .

CO＿2脱除量大、产品碳含量高、还原速率下降及入口温度上升是还原工艺的主要特点。

The main characters of Corex gas reduction process are large amount of CO_2 removal , high carbon content in DRI , low reduction rate , and tem-perature rising at gas inlet of shaft furnace .

在此基础上，对模型的操作条件进行优化：依次分析入口温度、催化剂活性、入口组成和入口压力对床层温度分布、CO转化率的影响。

On this basis , optimize the operating conditions of the model : followed by analysis the bed temperature distribution , CO conversion impacted by inlet temperature , catalyst activity , inlet components and inlet pressure .

二级Claus反应器入口温度控制在200-230℃，进一步促进硫化氢转化，硫的回收率可达70%；

Controlling inlet temperature of the second Claus reactor at 200 - 230 ℃ to promote farther H2S conversion and get 70 % of sulphur recovery ;

没有催化剂时入口温度在900K以上重整反应才能开始，反应速率慢，重整产物中H2和CO的体积分数少。

The reforming reaction can start without catalyst until the reformer inlet temperature reach 900K , H2 and CO content in the reformer product is small .

有催化剂时入口温度在600K以上重整反应即可进行，反应速率快，重整产物H2和CO的产量大。

When the catalyst is adopted , the reforming reaction can start at the reformer inlet temperature of 600K , the reforming reaction rate is high , H2 and CO content increase .

一级Claus反应器入口温度控制在220-250℃，硫回收率为65%，COS、CS2的水解率为50%-60%；

Controlling inlet temperature of the first Claus reactor at 220 - 250 ℃ to obtain 65 % of sulphur recovery and 50 % - 60 % of COS and CS2 hydrolysis efficiency ;

针对旋转闪蒸干燥机温度控制具有较大的滞后性、非线性和时变性的特点，以Φ1000型旋转闪蒸干燥机为具体对象，选用PLC作为温度控制器，并对其入口温度采用了自适应模糊PID控制算法。

Based on the characteristic of the delay , nonlinearity and time-varying in the temperature control system of spin flash dryer taking PLC as the temperature controller , the adaptive fuzzy PID control method is adopted to the entrance temperature of Φ 1000 type spin flash dryer .

以离散的CO浓度为状态变量，反应器入口温度为决策变量，催化剂费用为目标函数，构成DP网络。

The discrete concentration of CO was used as state variable , the inlet temperature of reactors as decision variable and the cost of catalysts as return function , the dynamic programming network for the water gas shift system of ammonia plant was set up .

HPL-1催化剂活性较高，能使加氢装置入口温度降低，减少能耗。

HPL-1 catalyst has higher activity . The inlet temperature of hydro genation plant has been decreased and the energy consumption reduced .

但在流场初值为1000K，燃料入口温度下降到700K时，甲烷转化率依然有81%。

However , while the initial temperature of flow field is 1000K , the inlet fuel temperature down to 700K , the methane conversion rate is still 81 % .

先进燃气涡轮的入口温度可超过1700K。

The turbine inlet temperature of future gas turbines is expected to exceed 1700K . None of the traditional metal could work in this condition .

采用该技术制造单晶叶片，可使燃气涡轮入口温度提高222～333℃，达到2100～2300K。

With this technology to manufacture single crystal blades and vanes , turbine inlet temperature can be increased by 222 ￣ 333 ℃, and can reach as far as 2100 ￣ 2300K .

滤液在喷雾干燥塔430℃的入口温度下喷雾热分解，再经过400℃下的流化床处理9min，可得到含量为99.5%（质量分数）高活性的氧化锌。

Then the filtrate was injected into a spray drying tower at entrance temperature 430 ℃ . The obtained powder was heated at 400 ℃ in a fluidized bed for 9 min. The active zinc oxide was obtained with a purity of ( 99.5 % . )

在聚酯变形工艺中最佳的假捻器入口温度

Best Inlet Temperature of False Twister in Polyester Distortion Technique

低温发动机试验推进剂入口温度控制

Propellant inlet temperature control for cryogenic rocket engine tests

烟气制酸转化器入口温度建模与优化设定

Modeling and Optimization for the Temperature of Converter Inlet on Metallurgical Acid Plant

入口温度分布对连续铸轧坯表面热带形成的影响

Initial Temperature Effect to Formation of Hot Strip in Continuous Roll Casting Process

干燥机入口温度是否超过规定值。

White dryer entrance temperature exceeds the specified value .

燃料入口温度的降低对燃烧效率有一些负面影响。

The reduction of inlet fuel temperature has some negative effect on combustion efficiency .

磨煤机入口温度偏低对制粉系统的影响

The Effect of Lower Inlet Temperature of Pulverizer Upon the System of Coal Powder Preparation

结果表明：总温升随入口温度的降低而近似线性地升高。

The model shows that total temperature jump almost increases linearly with decreasing entry temperature .

管内介质为不含水的化工原料，入口温度为90℃；

The tube side media is dry chemical feedstock and its inlet temperature is 90 ℃ .

循环水入口温度；

Inlet Temperature of Circulating Water ;

精轧入口温度；

Finish rolling entry temperature ;

流体组分含量及入口温度对天然气凝析液输送管道立管系统流体流动特性的影响

The influence of fluid component content and inlet temperature on the flow in gas condensate pipeline-riser system

气体入口温度及熔盐流量的影响不显著；

Gas inlet temperature and flow rate of molten salt have no remarkable influence on reactor performance ;

同时相变段长度还取决于入口温度和边界条件等因素。

The length of the phase-change region is also affected by the inlet temperature and the boundary conditions .

流体入口温度对换热器热力学性能影响的分析

The Analysis on the Effect of Cold and Heat Fluid Inlet Temperatures on the Thermodynamic Performance of Heat Exchanger