低碳钢板

介绍采用化学转化和A，B两种不同的交流氧化法，在冷轧低碳钢板上制备太阳谱选择吸收薄膜的工艺；

Technology for preparing solar spectrum selective absorbing film on the cold rolled mild steel plate has been introduced by means of chemical conversion as well as A and B alternating current oxidations ;

冷轧低碳钢板表面结露行为与钢板表面粗糙度分布有关，但与钢板的耐大气腐蚀性能并无直接关系。

The dewing behaviour had relationship with surface roughness of mild steel plates , however , it had no direct relationship with atmospheric corrosion resistance .

热连轧含Nb低碳钢板卷奥氏体再结晶研究

Austenitic recrystallization during hot strip continuous rolling in low carbon Nb steel

CSP工艺不同冷轧压下率低碳钢板退火织构的演变

Annealing texture of CSP low carbon steel sheet under different cold rolling reduction ratio

CSP热轧低碳钢板轧制过程中析出行为分析

Analysis of precipitate behaviors of hot rolling of low carbon steel produced by CSP

CSP低碳钢板的组织和性能

Microstructure and Mechanical Properties of Low Carbon Steel Strips Produced by EAF - CSP Process

采用大功率CO2轴快流激光器进行了低碳钢板的三维激光成形的规律研究。

The ruler on three - dimensional laser bending of low carbon sheet metal was studied using high power CO2 laser machine .

冷轧低碳钢板闪光焊HAZ的显微特性

Microstructure characteristics of Flash Welded HAZ of cold rolled low carbon sheets

热轧板带钢的生产工艺CSP技术生产热轧低碳钢板的组织细化研究

Analysis on the refined Microstructure Evolvement of low carbon steel hot rolling strip produced by CSP Technology

CO2气体保护的激光焊接12mm厚低碳钢板

Nd : YAG Laser Welding of 12 mm Low-Carbon Steel Plate with CO_2 Shielding Gas

利用金相显微镜和电子显微镜等方法对微Ti低碳钢板的微观组织和第二相粒子的沉淀行为进行了研究。

The microstructure and precipitating behavior of second phase particles in low carbon sheet steel containing micro-amount of Ti was studied by means of optical and electron microscope .

结果表明：钢A和钢B冷轧低碳钢板焊接HAZ具有相同的显微组织特征，但铁素体晶粒大小不同。

The results obtained show the microstructure characteristics of the welded HAZ of the cold rolled low carbon sheets ( steel A and B ) are same , but the ferrite grain sizes are different .

研究了紧凑式热带生产（CSP）热轧超薄规格低碳钢板的微观组织、二相粒子的析出及强化对力学性能的影响。

The effect of microstructures , precipitation and strengthening mechanism of precipitates on mechanical properties of ultra thin hot strip of low carbon steel produced by Compact Strip Production ( CSP ) technology was studied .

采用金相显微镜、H&800透射电镜和正电子湮没方法分析了CSP热轧低碳钢板金相组织、析出物形貌、尺寸、分布及位错密度。

The microstructures , precipitates of thin foil and dislocations density of hot strip of low carbon steel produced by CSP were observed using optical microscope , H-800 transmission electron microscopy and positron annihilation technology ( PAT ) .

FTSR线温轧工艺生产低碳钢板的组织分析

Analysis on Microstructural Evolution of Low Carbon Steel Produced by Flexible Thin Slab Rolling with Warm Rolling Technology

计算结果表明，CSP热轧低碳钢板卷细晶强化和沉淀强化占59%，常规工艺该项占55%。

Calculated results show that the contributions of fine grain strengthening and precipitation strengthening of low carbon steel strip produced by CSP process make up 59 % of all strengthening factors , while that by conventional process make up 55 % of all factors .

试验结果表明，使用本活性剂可使焊缝熔深比常规的TIG焊增加3倍，对12mm以下的低碳钢板对接无须开坡口，可一次焊接完成并能单面焊双面成型。

The testing results indicate that the penetration is increased 3 times compared with the conventional TIG welding and , for the plates of 12 mm thick , the fully penetration can be got in a single pass without groove preparation .

对FTSR线采用铁素体轧制工艺生产的3.0mm低碳钢板进行了微观组织分析和力学性能测定。

The microstructure of 3.0 mm low carbon steel strip , produced by ferrite rolling process on flexible thin slab rolling ( FTSR ) line at Tangshan Iron and Steel Co. , was analyzed by means of optical microscope , scanning ( electron ) microscope .

表面污染物对冷轧低碳钢板耐大气腐蚀性能的影响

Influence of surface contamination on atmospheric corrosion performance of cold-rolled steel plates

含铌低碳钢板控制轧制的研究

Study on controlled rolling of Nb-bearing low carbon steel plates

激光切割低碳钢板工艺试验研究

Experimental research on the technology of laser cutting of low carbon steel plate

微钛低碳钢板的微观组织观察与分析

Observation and Analysis of Microstructures of Low Carbon Sheet Steel Containing Micro-amount of Ti

冷轧低碳钢板表面形貌与其耐大气腐蚀性能的关系

Relationship between the surface roughness and the atmospheric corrosion resistance of cold-rolled steel plate

两台一体式变压器并联使用时可焊3mm+3mm的低碳钢板。

Two shunt-connection integrated transformers can weld 3 mm + 3 mm low-carbon steel .

紧凑式热带生产优质热轧超薄低碳钢板的显微组织分析

Mechanism of Producing High Quality Ultra-thin Hot Strip of Low Carbon Steel by CSP Technology

液态铸轧低碳钢板的研究

Study on the mild steel sheet rolling directly from the cast slabs with liquid core

卷取温度对薄板坯连铸连轧含硼低碳钢板性能的影响

Effect of coiling temperature on properties of low carbon steel with boron produced by TSCR

热轧低碳钢板卷麻面产生原因分析

Analysis of the Causes of Scale Mark Formation on the Surface of Hot Rolled Low Carbon Coils

控制轧制对含钒低碳钢板组织与性能的影响

The influence of controlled rolling process on the microstructure and properties of vanadium micro-alloyed low-carbon steel plate

用于低碳钢板气割时，气割成本随板厚不同而变化。

When propane gas cutting low-carbon steel plate , the cost varies with the thickness of the steel plate .