风机

fēng jī
  • fan;draught fan
风机风机
风机[fēng jī]
  1. 由强力风机把空气吸出去。

    The air is sucked out by a high-powered fan

  2. 介绍了一个基于Internet的风机网上选型系统的设计和实现。

    The design and implementation of fan selecting system based on internet are presented .

  3. 风机检修的的标准流程是什么

    The wind turbine generator overhauls what is the standard flow ?

  4. Air(初三适用)周边区风机盘管机组空调的自动控制方法

    Automatic control for perimeter zone air conditioning

  5. 参数化设计技术在离心风机CAD系统中的应用

    The Parameter Design Technology in Developing TLT Blower CAD System

  6. 以实现自适应BP算法在冷却塔风机效能建模中的应用为例,介绍了实现过程,为实现其它智能算法提供参考。

    It offers guidance for other intelligent algorithms ' realization .

  7. PLC在转炉风机煤气回收中的应用与研究

    Application and study of programmable controller on converter fan motor and coal gas callback

  8. 及叶宽系数K的取值范围。通过试验筛选出四个基本型、36种规格性能的喷雾机轴流风机系列。

    Basic models with 36 specifications of axial flow fans for sprayer haTe been selected based on tests .

  9. 高炉7000m~3/min轴流风机安装调试经验

    Experience on installing and testing 7000m  ̄ 3 / min Sulzer axial blower of the blast furnace

  10. 从而计算风机不同压力下不同的SLIP值,正确客观地评定了风机的质量情况和容积效率等。

    The different SLIP at different pressure can be calculated to assess blower quality and volume efficiency etc. correctly .

  11. 南端在罗家沟(F(210)断层)掘进一条回风井,设置抽出式风机;

    Pierce a return air shaft at Luo Jia Gou ( fault F210 ) in the south , establish the exhausting fan ;

  12. TLT离心风机CAD系统的升级优化

    Upgrade of TLT Blower CAD System

  13. 同时通过改变CAD模型中的径向间隙,对不同径向间隙的轴流通风机流场进行对比,得到了优化的风机设计。

    At the same time by changing the CAD model of radial clearance , the different radial clearances of the axial flow fan are compared for the Fan performance optimization .

  14. HTR-10主氦循环风机的设计、试验和运行

    Design , Test and Operation of Helium Circulator for HTR-10

  15. 以数字信号处理器DSP研制便携式旋转风机故障诊断分析仪,并详细阐述了系统的硬件结构以及软件设计思想。

    Digital signal processor ( DSP ) was adopted to design portable rotating air blower fault diagnosis instrument , and the system hardware structure and the software designing ideas were expounded .

  16. VSR风机调节装置的应用

    Application of Regulating Device of VSR Blower

  17. 通过对流体力学中沿程阻力系数和泵与风机工作点等问题的求解,介绍了EXCEL单变量求解器和曲线拟合的方法。

    Through calculating friction factor and operating point of pump or fun of two examples on fluid mechanics , methods using solver and curve-fitting in EXCEL were introduced .

  18. 本文介绍了RTM法成型玻璃钢轴流风机叶轮轮毂的模具设计和轮毂的成型工艺。

    Mould design for impeller-hub of axial-flow fan were introduced . Besides , moulding processing of hub was discussed .

  19. 600MW机组风机叶片断裂分析

    Cracking Analysis of Air Fan Blades of 600 MW Generating Set

  20. 经过比较可知,VRV中央空调系统,热损失较小,负荷调节灵活,在建筑空调系统中使用效率较风机盘管中央空调系统高。

    The results were that VRV air conditioning system has more efficiency than the fan-coil system .

  21. 采用有限元程序LS-DYNA对风机金属块撞击风机叶片的非线性瞬态响应进行了数值仿真研究,结果表明:接触冲击算法能较为真实反映风机叶片金属块撞击过程;

    The numerical emulating research on the nonlinear transient response for fan metal piece impact is carried out using LS-DYNA finite element program .

  22. 高炉风机由于PLC控制系统检测到误信号而故障停机,通过对程序的修改,可避免同类事故的再次发生,至今运行效果良好。

    The blast furnace blower had a stoppage due to wrong signals detected by the PLC control system . Modification of programs could avoid similar failures and the blast furnace blower system for stoppage has been running well .

  23. 锅炉风机节能研究:YT型液粘调速离合器的应用

    Investigation of Boiler Fans Energy - saving : The Application of YT-type Liquid Viscosity Speed Regulation Clutch

  24. 高压变频器在30t顶底复吹转炉除尘风机中的应用

    Application of High Voltage Frequency Converter in Dusting Blower of 30 t Top and Bottom Blowing Converter

  25. 通过对我司家用空调室外机两种风扇&传统风扇和新设计风扇的CFD计算对比分析。从流场分析得出新设计风扇在压力分布、风机效率优于传统风扇。

    By CFD analysis between the traditional fan and the new design fan , which used in outdoor unit of GREE , the latter is superior in pressure distribution and efficiency of fan .

  26. 本文用MATLAB/SIMULINK软件对系统中的部件,包括风机、单相IGBT变流器、三相IGBT变流器、同步发电机、整流器等都建立了模型。

    Wind generation system components , including wind turbine , 1-phase IGBT inverter , 3-phase IGBT inverter , synchronous generator , and rectifier , are modeled in this thesis using MATLAB / SIMULINK .

  27. 对风机轴承座处的振动信号进行定期测量,获得多组风机在无故障和有故障条件下的振动信号。运用FLUENT软件对两叶轮背部间隙流场进行计算。

    The vibration signals on the bearing box of the fan was measured periodically . The leakage gas flow field between the bearing box and the impellers is solved by the software FLUENT .

  28. HTD系列化铁炉节能风机特点及应用

    Characteristic and Application of Energy-saving Blower Used for HTD Series Iron-molen Stove

  29. 简要描述了清华大学10MW高温气冷实验堆的氦循环风机远距离控制系统的设计与调试概况。

    Verifications and design of the remote control on 10MW high temperature gas cooled test reactor helium circulator are described in this paper .

  30. 在此基础上,提出了将机器学习理论应用于风机状态识别的方法,设计并实现了一种基于支持向量机(SVM)的风机状态识别分类器。

    On the foundation of above , study on Machine Learning and its applications in status-recognition of fan are presented , and classifier fan state recognition based on Support Vector Machine ( SVM ) is designed and implemented .