双槽

熔喷双槽形喷嘴形成的流场可以看作两股平面射流的合成。

The flow field of the air jet from dual slot die in melt blowing process can be considered as the synthesis of two plane jets .

结果表明，应用涡偶代替射流推导出的气流速度分布公式能够较好地描述熔喷双槽形喷嘴气体射流流场，可以用于完善熔喷气流拉伸数学模型。

The results show the formula of air velocity distribution developed by substituting jet with vortex pair can describe the flow field of the air jet from dual slot die in melt blowing process and can be used to consummate the air drag mathematical model of melt blowing .

采用主副双槽二段循环吸收，在提高Mn浸出率的同时，能确保较高的SO2脱除率；

Two troughs of absorption were used to improve the leaching rate of Mn and the desulfurization rate .

双槽电沉积制备单层膜厚1μm的NiMoP/Cu多层膜。

Ni-Mo-P / Cu multilayers were electrodeposited using dual bath in which each layer had the thickness of ( 1 μ m. )

在硼酸镀液中以单晶Si（111）为基底用双槽法制备Cu/Co多层膜，在镀液中分别加入了镀铜添加剂2000和镀钴添加剂5。

Cu / Co multilayers were prepared on monocrystalline silicon ( 111 ) by using double-bath method in boric acid solution with additives added .

以AAO膜为模板，通过双槽交流电沉积的方法，制备了Cu/Co多层纳米线，利用扫描电子显微镜（SEM）观察了纳米线阵列及单根纳米线的形貌。

The morphology of nanowires in pores of AAO was characterized by scan electron microscopy ( SEM ) .

本文用双槽电沉积的方法制备了Ni-P／Cu和Ni-Mo-P／Cu多层交替镀层。

In this thesis , Ni-P / Cu and Ni-Mo-P / Cu alternate multilayers were electrodeposited using twin bath technique .

充分利用窄V带传动的优点和一种新结构的可变直径双槽带轮，设计出摩擦窄V带式无级调速器。

Making a good use of the advantages of narrow V-belt and a new structure of double-grooved pulley with variable diameter , a stepless speeder with frictional narrow V-belt has been designed .

分析了槽的尺寸，槽的个数及槽内介质对MDM波导透射谱的影响，对于双槽结构，适当选取两槽间的距离可使槽间的干扰几乎可以被忽略。

It analyzes the influence to MDM waveguide transmission spectrum of the slot size , amount and its medium to the resonant frequency . The author chooses the distance between the slots which can ignore the interference .

介绍了双槽VBM平幅连续精练机的主要结构特点和操作要点，列举了织物经该机精练的有关物理特性和质量指标。

Describes the major structural and operational features of the Double-Trough Open-Width Continuous Scouring Machine VBM , as well as the physical property and quality index of the scoured fabric .

采用双槽控电位电沉积法在n-Si（111）基体上以NiFe薄膜为缓冲层制备了[Ni（80）Fe（20）/Cu/Co/Cu]n自旋阀多层膜，并确定了电沉积的工艺条件。

[ Ni_ ( 80 ) Fe_ ( 20 ) / Cu / Co / Cu ] _n spin-valve multilayers were fabricated onto n-Si ( 111 ) substrates covered with NiFe buffer layers by means of double bath potentiostatic electrodeposition . The electrochemical conditions were determined .

大型平炉双槽出钢的挡渣技术

Slag retaining technique for large open hearth with dual tapping spouts

双槽深波纹波导和多频段馈源的理论分析

Analysis of A Dual-Slot Depth Corrugation Guide and a Multi-Band Feed

环氧涂层金属体系的串联双槽电化学阻抗谱分析

EIS analysis of epoxy - coated metal system by series double-cell compartment

双槽电化学腐蚀法制备介孔硅的热导率

Thermal Conductivity of Meso-Porous Silicon Prepared by the Double-Tank Electrochemical Corrosion Method

双槽电化学腐蚀法制备多孔硅的孔隙率研究

Study on the Porosity of Porous Silicon by Double-tank Electrochemical Corrosion Method

采用双槽密封条密封，防护等级高；

Adopts diglyph sealing , for high degree of protection ;

大型双槽渡槽地震反应分析

Seismic response analysis of large-scale aqueduct with double troughs

大跨双槽渡槽横向地震响应分析

Lateral seismic response analysis of large-scale double cell aqueduct

冷床上料系统双槽上卸钢装置的改造

Innovation of the charger-discharger with double slides in the charging system of cooling bed

双槽平幅连续精练机及精练效果

Double-Trough Open-Width Continuous Scouting Machine and Its Efficiency

双槽法电沉积Cu/Ni多层纳米线有序阵列

Electrodeposition of Ordered Arrays of Multilayered Cu / Ni Nanowires by Dual Bath Technique

大型双槽高强度搅拌磨机的开发与应用

Development and Application of GJ5 × 2 Large-Scale and Higher Intensity Double Cells Stirring Mill

分别采用单槽法和双槽法电沉积制备Cu/Ni多层膜。

In this paper Cu / Ni multilayers were prepared by using single-bath and double-bath methods respectively .

当雨过天晴，旋转双槽滑轮，防雨材料自行收拢。

When a rainy day is converted into a sunny day , the double groove pulley is rotated ;

最后，用模糊数学的方法对结构不同的吸风双槽进行综合性能评判。

Finally , Comprehensive evaluation is done to the double suction grooves with different structures with method of fuzzy mathematics .

本文阐述了单面双槽弹簧扁钢的轧制工艺及孔型设计对产品质量的影响。

This paper discusses the effect of rolling process and pass design on product quality for the flat spring steel with single-side and two-slot .

对双槽熔喷工艺的空气流场进行三维数值模拟，得到了空气流场的三维分布结果。

Through the numerical simulation of air flow field in melt blowing with dual slots , the three dimensional distribution of air flow field is obtained .

本文主要对双槽形熔喷非织造工艺中的空气流场、熔体流场特点及纤维成形机理进行研究。

The characteristics of air flow field in melt blowing with dual slots and the mechanism of fiber formation in melt blowing are mainly studied in this dissertation .

结合双槽凸轮的参数设计和其曲线的基本走向，得出了内、外凸轮曲线的方程。

The curvilinear equations of the inner and outer cams are obtained based on the analysis on the parameter design and the curve shape of the double-slot cam .