串口连接
- 网络serial connection
![串口连接](../cache/1400145.jpg)
-
方案采用一个嵌入式的MODEM作为系统传输数据的MODEM,MODEM和单片机通过串口连接,实现数据的实时传输。
Adoption of MODEM as an embedded system for transmission of data MODEM , MODEM and MCU through serial connections , the real-time transmission of data .
-
通过家电控制器单片机的串口连接RS-485网络,利用多机串口通信实现了对系统功能的扩展。
Using the second serial port of the controller to connect the RS-485 network , the fuction of the system was extended .
-
在该DNC架构中,数控设备通过RS-232串口连接到串口服务器,串口服务器直接连接到基于TCP/IP协议的车间层局域网。
In it , the NC machines are connected to the serial device servers , and the serial device servers are connected to the LAN which is using TCP / IP protocol .
-
它的硬件主要由MMI板和TETRA主板构成,MMI板提供了人机交互的接口,TETRA主板实现了TETRA的协议栈,它们之间通过串口连接。
The hardware consists of MMI board and TETRA main board , MMI stands for man machine interface , TETRA main board implements the TETRA protocol stack . They are connected by serial port .
-
该装备主要以动态摄像技术及微机控制为核心,通过RS-232串口连接上位机与下位机(LPC2104单片机),实现了定位及钻孔的自动化,提高了加工效率。
The key technology of this machine is dynamic photographing and microcomputer control , and connecting upper microcomputer and singlechip ( LPC2104 ) by RS-232 serial port . The machine achieving drilling locating automatization , improving machining efficiency .
-
检验设备与计算机的串口连接
The connection between laboratory equipment and computer by serial ports
-
一条串行线(空调制解调器电缆)将通过机器的串口连接它们。
A serial line ( null-modem cable ) connects the machines through their serial ports .
-
工控领域中,很多工控设备的物理接口层都是使用串口连接。
In the field of industrial control , the physical interface layer of much equipment uses a serial port connection .
-
系统采用串口连接条码枪来扫描冰箱条码和抽空计条码进行配对操作。
The system adopts serial port to connect barcode gun with server to scan refrigerator bar and pump bar which is matched with refrigerator bar .
-
所介绍的飞行器固态数据存储器系统能够实现对飞行器机载信号进行数据采集及存储,并通过长线与地面计算机的RS-232串口连接,实现通信。
This paper introduces a solid state data memory system which can sample and encode the analog signal on craft , and then store the data in the memory equipment .
-
本文介绍了PC机之间RS-232c标准的串行通信的几种连接方式和利用光纤作为通信媒介的串口连接方法和框图,最后介绍了一个串行通信编程的源程序。
Several methods of connecting PC through serial ports with RS 232c standard are presented . Optical fiber as a medium has many advantages , so we select optical fiber as transmission medium when directly connecting PC through serial ports . A test program is presented in the last part .
-
上位机通过RS-485总线接口与下位机采集卡的串口模块连接。
The host computer connects with serial modules of the data acquisition card via RS-485 bus interface .
-
上层管理分析系统的通信实现是软件开发中的难点问题,本套系统通过串口方式连接到保护装置,采用Modbus协议完成各种相关数据的传输过程。
The system connects to the serial port of the protection device , and uses Modbus Protocol to complete all data transmission .
-
通过让DSP信号处理模块对速度信号进行采集,用串口通讯连接上位机,让上位机来完成对信号的接收、处理及图形绘制等工作,进而最终得到电机的各种运行特性。
DSP signal processing module is responsible for collecting the speed signal . Serial communications connects PC. PC accomplishes the work of signals receiving , processing and plotting , etc. And then we finally gain the work of various operation characteristics from motor .
-
中心协调器与上位机PC机通过串口相连接。
Center coordinator connected PC with the serial port .
-
嵌入式交叉调试器解决了在低配置目标主机上不能直接运行调试器的问题,实现在主机端运行调试器,目标端使用调试代理,两者通过网络或串口进行连接完成嵌入式交叉调试的任务。
Embedded cross debugger resolves the problem that the debugger can not directly run on target host with low configuration . Embedded hosts run the debugger and the target client using the debug agents .
-
开发了一种接收并处理光纤陀螺开环信号的数字化系统,用此系统实现GPIB总线到USB通用串口总线的连接,从而实现人机的友好界面。
A digital system that receives and processes the open loop signal of fiber optic gyroscopes was developed . GPIB bus connects with USB universal bus through the system to realize the human-machine amity interfacing . All the interfacing function of the GPIB bus is realized through CPLD .
-
一台通用电脑,他通过串口或网络连接和目标机通讯。
A general-purpose computer that communicates with the target via a serial port or network connection .
-
除错器在宿主机上运行并且通过串口或网络连接到目标机上。
The debugger runs on a host computer and connects to the target through a serial port or network connection .
-
用串口直连电缆连接到交换机串行控制端口(9600、8-N-1、无流控制)。
Connect to the switch using the serial console port with a straight serial cable ( 9600,8-N-1 , no flow control ) .
-
控制芯片通过串口与GPS模块连接,接收GPS模块获得定位信息;
The control chip is connected with the GPS module through the serial port for receiving the locating information of the GPS module .
-
控制芯片通过串口与通讯电路连接;
The control chip is connected with the communication circuit through the serial port .
-
PC机通过串口与无线模块连接组成的主控端。
The main control terminal is composed of wireless module and PC through serial port .
-
使用直接电缆连接,可以方便快捷地在两台计算机之间建立直接的串口或并口电缆连接。
Direct cable connection enables you to quickly and easily establish a direct serial or parallel cable connection between two computers .
-
USB100模块提供两种PC机应用程序编程:虚拟串口方式和动态连接库方式,降低了编程难度。
USB 100 provide the two applied programme manners of suppositional COM port and dynamic link library , which reduces the difficulty of the applied program .
-
6000米无缆水下机器人完成了太平洋洋底考察。使用直接电缆连接,可以方便快捷地在两台计算机之间建立直接的串口或并口电缆连接。
Our 6,000-meter computerized underwater vehicle successfully explored the floor of the Pacific Ocean . Direct cable connection enables you to quickly and easily establish a direct serial or parallel cable connection between two computers .
-
此外还设计了RS232串口通信电路,通过串口与PC机连接,以便在程序调试过程中观察实验结果。
In addition also devised a RS232 serial communication circuit , Through a serial port and PC connection , so in the program during the commissioning of the observation results of the experiment .
-
串口转WiFi/GPRS数据双网模块是串口设备连接WiFi和GPRS网络的有效设备,具有较好的应用前景。
Converted WiFi / GPRS data dual-Netcom Module is an efficiency serial interface device of connecting WiFi and GPRS network , which is endowed with promising future .
-
介绍基于RS-232串口控制的人影作业指挥系统的串口通信硬件电路连接、程序结构和地理模型。
In this paper , RS-232 communication system is introduced and conduction system of weather modification is realized on the Geographical Model .
-
为了得到激光波长的准确数据,本文使用了Buileigh公司的WA-4500波长计,并利用RS232串口把其波长数据传输到主控计算机,完成了串口硬件连接和通信软件编制。
And , to get correct wavelength data , Burleigh WA-4500 wavelength meter was used . With the efforts on hardware connection and software programming , the data was transported from WA-4500 to the main control computer through RS232 serial communication .