钼粉

mù fěn
  • molybdenum powder
钼粉钼粉
  1. 喷雾法制备活塞环用MP43喷镀合金钼粉

    The preparation of spraying alloy molybdenum powder by spray drying method

  2. 高温钼粉的性能对其成形及烧结的影响

    Effects of properties of high temperature molybdenum powder on its compacting and sintering

  3. PLC控制的液压钼粉压块机

    PLC Controlled Hydraulic Briquetting Press for Molybdenum Oxide Powder

  4. 本实验中采用粒径为2gm的Mo颗粒,在施镀以前要对钼粉进行预处理。

    Before plating pretreatment was carried out on the molybdenum powder .

  5. 碱催化剂NaOH和金属催化剂钼粉也显示出了较佳的催化性能,液化油收率大大提高。

    Base catalyst NaOH and metallic catalyst molybdenum powder also show preferable catalytic activities .

  6. 介绍了结晶态钼酸铵不同的SEM形貌及其在动态焙解还原制取钼粉中的应用情况。

    Various SEM appearances of ammonium molybdate crystalline and their application in molybdenum powder preparation by dynamic roastdissociation-reduction are introduced in this paper .

  7. 对钼粉等离子喷涂的适当气体流量应当在30L/min左右。

    The appropriate flux should be maintained around 30L / min.

  8. 数学分析指出,若将铁粉和-325目钼粉混合并于1120~1180℃烧结,此时扩散均匀性判据值Dt/l~2远小于1,Mo难以扩散均匀。

    If it is far below one , diffusion proceeds without homogeneity . When mixed Fe and Mo powders were sintered at 1120 & 1180 ℃, Mo could diffuse into iron matrix .

  9. 氢气还原蒸发态MoO3制取超细钼粉的探索

    Discussion on the production of superfine molybdenum powder by means of the reduction of molybdenum trioxide in evaporative state using hydrogen

  10. 介绍了La2O3对还原钼粉形貌和粒度的影响,以及La2O3对钼粉制坯的影响。

    This study gives an introduction to the effect of La 2O 3 on its shape and size after reduction and also that of La 2O 3 on the blank making of Mo Powder .

  11. 简述了La2O3的一些特性,结果表明:随着La2O3含量的增加,钼粉粒度逐渐减小,颗粒形貌规则化;

    It briefly introduces the characters of La 2O 3.The result indicates : With the increase of the content of La 2O 3 , the size of Mo powder gradually reduction , the shape of Mo Powder becomes regular .

  12. 用原料添加法提高钼粉粒度的探讨

    Investigation of Increasing Molybdenum Powder Size with Added Raw Material Method

  13. 钼粉粒度和松装密度对钼条加工性能的影响

    The effect of particle size and bulk density on molybdenum powder

  14. 锻造工艺对钼粉烧结体的材料性能的改善

    Material properties improvement of molybdenum powder sintered body by forging process

  15. 无低温过渡高温还原钼粉试验研究

    Test on molybdenum powder without low temperature transition and high temperature reduction

  16. 脉冲红外法测定钼粉中氧含量及其分量研究

    Impulse Infrared Determination of Oxygen in Pure Molybdenum Powder and Its Make-Up

  17. 钼粉形貌对钼丝断裂性能的影响研究

    The effect of molybdenum powder morphology on fracture properties of molybdenum wire

  18. 针形钼粉的制备及其应用

    The preparation of acerate molybdenum powder and it 's application

  19. 等离子喷涂铁基合金粉混钼粉涂层组织的研究

    Coating structure investigation of ferritic alloying powder by plasma-spraying

  20. 浅析钼粉工艺原理与生产实践

    Study on technology of molybdenum powder and production practice

  21. 因此,对钼粉颗粒进行分散处理十分必要。

    Therefore , the scattering processing of the molybdenum powder particles is necessary .

  22. 钼粉制取工艺模型化

    The modelling preparation process for the molybdenum powder

  23. 生产工艺对钼粉平均粒径及其加工性能的影响

    The effect of production technology on mean grain size and workability of molybdenum powders

  24. 气相色谱法测定金属钼粉中氧含量

    Gas chromatographic determination of oxygen in powder molybdenum

  25. 高能机械化学法制备微纳米氮化钼粉体的研究

    The research in micro / nanometer molybdenum nitride powder prepared with high-energy mechanochemistry method

  26. 还原工艺对钼粉粒度和氧含量的影响

    Effect of reduction processing on the grain size and oxygen content of molybdenum powder

  27. 钼粉的制备技术及其进展

    Preparation technology of molybdenum powder and its development

  28. 对钼粉小白点问题的研究与实践

    Study on white impurity of molybdenum powder

  29. 大粒度钼粉生产棒坯的工艺及质量研究

    Research on the Technology and Quality of Producing Rod Billets by Large Size Molybdenum Powder

  30. 钼粉的低温活化烧结研究&Mo-Ni-P系的低温烧结特性

    STUDY ON LOW TEMPERATURE ACTIVATED SINTERING OF MOLYBDENUM & The Sintering Characteristics of Mo-Ni-P System