辊道

邯钢CSP输出辊道改进和优化

The improving and optimization of run out roller table in Hangang CSP line

浅析YGa型辊道用异步电动机每小时允许起动次数的计算方法

Simple Analysis of The Calculating Method of The YGa Roller Table Asynchronous Motor Starting Frequency

H型钢轧机工作辊道升降机的校核与改造

Verification and Alteration of Screw Jacks of H Beam Mill Work Table Roller

淬火机辊道速度自校正PID控制系统

The self-adjusting PID control system of the speed of quenching machine roller

陶瓷辊道窑CAD系统研究

Research on Ceramic Roller Kiln CAD System

武钢热轧厂精轧线飞剪及E辊道主干数字化改造

Digital Transformation of Crop Shear and E Table Master in Hot Strip Mill of WISCO

交流伺服系统及PLC在浮法线冷端加速辊道上的应用

The Application of Servo and PLC System on Accelerated Roller on Cold-Side of Float Line

轧机运输辊道结构的改进H型钢轧机高速空心辊道辊子的研制

The development of the high speed hollow roller on the roller table of the H beam rolling mill

火焰热喷焊技术在CSP输送辊道上的应用

The Application of Flame Spray Welding Technology in CSP Running Table

冷却风机与STM辊道的同步控制

The cooling fan and the STM rooling of the sync control

HS合金在加热炉辊道上的应用

The Application of HS Alloy on the Roller Table of Reheating Furnace

提出了出粗轧区轧机及辊道的速度控制和电动APC控制策略；

The speed control strategy of mills and tabs in rough rolling section and APC strategy are given .

对陶瓷辊道窑的多变量解耦控制方法进行研究，并采用FPGA作为控制器，完成了基于FPGA的陶瓷辊道窑燃烧控制系统设计。

A multi-variable decoupling method is put forward and FPGA is used as a controller . The ceramic roller kiln combustion control system based on FPGA is designed in this master thesis .

提高辊道用变频调速三相异步电动机防水性能方法的研究台达BW系列变频器在电池极片轧辊机收放卷上的应用

Research on Improvement of the Water-Proof Performance of Variable-Frequency Adjustable-Speed Three-Phase Roller Induction Motor Application of Delta BW Series Inverters in Battery Pole Piece Roll Machine Rollout

采用FLUENT软件对辊道窑烧成带速度场和温度场进行数值模拟，并对其两种不同烧嘴布置的燃烧工况进行了研究。

This paper carry out simulate calculation to speed field and temperature field of roller kiln burning area with FLUENT software , and study its two different kind of burner disposal combustion operating mode .

采用标准K-ε湍流模型和P-1辐射模型对辊道窑烧成带内气体流场与温度场进行了数值模拟研究。

The standard K - ε turbulent model and the P-1 radiation model are adopted to simulate the turbulent flow and heat transfer of firing zone .

通过有限元法验证了应用于某轧钢厂加热炉辊道的UHMWPE轴承（替代原金属轴承）的合理性，论证了应用的可行性。

The rationality of using UHMW-PE bearing , replace the original metallic bearing , in the roller of heating furnace of rolling steel plant is verified by FEA method and the possibility of application is pointed out .

将该软件系统用于设计FRW2000型辊道窑获得了满意的设计结论。

Some satisfactory results using this system to design FRW2000 roller kiln are stated In this paper .

以辊道窑为例分析了在陶瓷工业窑炉中应用Ex分析的优越性，提出了基于Ex分析的陶瓷工业窑炉热经济分析的一般步骤与应用方法，并探讨了陶瓷工业窑炉的节能潜力。

Based on roller-kiln 's exergy analysis , the advantages of the method of exergy analysis about ceramic industrial kiln is analyzed , brought forward the general steps and usage of the thermal economic analysis of ceramic industrial kiln , and explored the potential of the energy saving .

唐钢高速线材厂轧钢生产线风冷运输辊道电动机采用变频调速控制，随着轧制速度的加快，0～50Hz可调频率范围的转速，不能满足生产的要求，因此对电动机进行了扩大调速范围的技术改造。

The air-cooled roll motor , installed in the high-speed wire factory of Tangshan Iron and Steel Company , uses transducer to control the speed , which with the range of 0-50 Hz can not fit the demand of production .

通过采用液压比例阀控制双辊道移钢装置，提高精整区能力，稳定350t冷摆剪运行节奏，解决轧制能力大于精整处理能力的问题。

Through using hydraulic proportion valve to control the double-roller moveable device , the ability of refine area is improved and movement frequency of 350t cool-shear is stabilized . It can solve the problem of rolling ability exceed to treatment ability of refine area .

通过改造上料辊道，加强外部协调，使待煤气停产时间减少了110h，吨板燃耗降低了1.51m3/h，提高了中板产量。

Through reforming the charging roller and strengthening the exterior coordination , the delay time of waiting gas is decreased by 110h , the fuel consumption per ton of plate is decreased by 1.51 m 3 / t , and the production of plate is increased .

水煤浆在陶瓷辊道窑上燃烧的脱硫过程研究

Research on Desulfurization in CWS Combustion in a Ceramic Rolling Kiln

固体润滑轴承在轧钢机运输辊道上的应用

Application of solid lubrication bearing in run table of rolling mill

着重介绍了辊道调速系统的构成。

The configuration of roller table speed regulation system is emphasized .

用变频器对钢管输送辊道电源进行改造

Use Transformer to Improve power of Steel Pipe Convey Roller Track

辊道窑窑内壁温度场计算机模拟

Computer simulation for temperature field of inner wall of roller kiln

大型重轨加工线升降辊道设计

Rise and Fall Roller Design for Heavy Section Rail Process Line

复杂环境下辊道基础梁部分预裂切割爆破

Presplitting Cutting Blasting for Roller Track Foundation Beam at Complex Environment

中固轧辊，中支轧辊精轧机组中间辊道侧挡板滑移系统改造

Finishing Mill Transitional Roll Table Side Guide Plate Slipping System Transformation