磨削裂纹

防止和消除合金钢齿轮磨削裂纹的探讨

Prevention and Avoidance of Grinding Cracks in Gears Made of Alloy-Steel

柴油机油泵阀磨削裂纹分析

Analysis of grinding cracks of oil pump valve of diesel engine

针对大载荷循环加载，采用修正后的Morrow方程进行等效转换，并进行疲劳等效实验，得出超声磨削裂纹断裂寿命与应力振幅的关系。

As the large load , the equivalent experiment is designed according to the modified function of Morrow , and the relationship between the crack fracture life and stress amplitude can be obtained .

活塞销表面磨削裂纹分析及改进措施

Analysis of Crackles on Piston Pin 's Surface and Improving Measures

减速器蜗杆磨削裂纹的分析与预防

The analysis and prevention on the grinding crack of decelerator worm

轴承零件磨削裂纹产生机理与防治措施

Creation mechanism of grinding crack of bearing parts and preventive measure

模具磨削裂纹止裂与封闭试验研究

Experimental Study of Grinding Crack Arresting and Closing in a Die

磨削裂纹的脉冲放电止裂与强化

Arresting and Reinforcing of Grinding Crack through Pulse Current Discharge

柴油机零件磨削裂纹分析及预防

Analysis and Prevention of Grinding Crackles in the Parts of Diesel Engine

连杆螺母高频淬火后磨削裂纹产生的原因及改进方法

Reason and Improvement of Grinding Crack Producting in Nut after Induction Hardening

柱塞斜槽磨削裂纹的成因及对策

Causes and Countermeasures of Grinding Cracks on Skewed Slot of Plunger Piston

渗碳淬火齿轮磨削裂纹的防止

Methods of Preventing Tooth Grinding Cracks for Carburized Hardened Gear

柴油机凸轮轴磨削裂纹成因分析

Analysis of Cause of Crackle of Diesel Engine ′ s Cam Shaft

工程陶瓷；裂纹扩展；磨削裂纹；

Structure ceramics ; Crack growth ; Grinding cracks ;

飞机桨壳螺帽磨削裂纹分析

Analysis on cracks of nut for aircraft propeller case

中频淬火凸轮轴磨削裂纹产生原因及对策

Cause of Grinding Cracks on Medium Frequency Induction Hardened Cam Shaft and Countermeasure

机械油泵定子磨削裂纹的分析

Analysis on grinding cracks of the oil pump stator

消除渗碳主轴端面磨削裂纹的方法

Method of eliminating grinding cracks on cemented spindle faces

解决圆角淬火曲轴磨削裂纹的措施

Solution for the Grinding Crack of Hardened Corner Crankshaft

磨削裂纹产生机理和预防措施

Mechanism of Grinding Crackle and Its Precautionary Measures

磨削裂纹的产生与防治措施

The emergence and prevention method of grinding cracks

刀具产生磨削裂纹的原因及预防措施

Causes and Preventive Measures of Tool Grinding Cracks

齿轮磨削裂纹的产生原因及防止措施

Reasons of Cracks During Grinding and Preventive Measures

工程陶瓷磨削裂纹形成过程研究

Study of grinding cracks for engineering ceramic materials

渗碳钢件磨削裂纹的产生及其工艺分析

Occurrence of Crack on Carburized Steel Pattern in Grinding Process and Its Technique Analysis

在实验研究的基础上确定了防止磨削裂纹的措施。

On the basis of test , some measures to avoid grinding cracks are established .

这些磨削裂纹会降低零件的使用寿命，或者造成零件报废。

These grinding cracks will reduce the life of components , or cause parts scrapped .

介绍了产生磨削裂纹的原因、影响因素及控制措施。

The article explains the causation of grinding crack , affecting factor and controlling steps .

磨削裂纹形成机理商榷

Discussion of Grinding Crack Forming Mechanism

球铁凸轮的磨削裂纹

Grinding cracks of ductile iron cam