电路接口

有源R型温度/频率转换电路接口设计

Design of an Active-R Temperature / frequency Circuit and Its Interface

基于FPGA的惯导系统温控电路接口设计

FPGA-based Design of FOG-INS Temperature Control Circuit Interface

介绍了USB系统中的电路接口。

Circuit interface of USB system-s in introduced .

深入探讨了DSP技术和计算机的总线接口技术，设计了PC及DSP的硬件电路接口。

Deep research into DSP technology and computer bus technology , design the hardware and circuit interface of PC and DSP .

包括键盘接口，液晶显示器接口，电源监控及数据掉电保护电路接口，扩展数据存储器，与CPLD的接口等。

Including the interface to keyboard and liquid crystal displayer power source monitoring and reset circuits , the extended RAM , the connection to CPLD etc.

介绍BluetoothASIC的结构特性以及DAWNS&B的结构原理、硬件电路接口和软件系统。

The architecture properties of Bluetooth ASIC is introduced and the architecture principle , hardware circuit interface and software system of DAWNS-B are discussed in this paper .

3COM路由器广域电路接口Loopback测试

The Loopback Test of Wide Area Circuit Interface of 3 COM Router

USB2.0规范的电路接口

Circuit interface of USB 2.0 specification

之后为了搭建硬件的实验平台进行了微处理器和无线射频芯片等主要元器件选型和电路接口设计，并且完成了硬件电路设计和PCB电路板的制作和测试。

Meanwhile , we select microprocessor chips , radio frequency chips and other major components for experimental platform . The work including the design of the hardware circuit and PCB plate making is completed .

本文将电路接口技术与硬件可编程技术相结合，提出了用可编程芯片来控制IDE硬盘进行高速数据记录，能够满足机载数据记录设备重量轻、容量大、速度快的要求。

Based on the interface technology and hardware programmable technology , this thesis introduces a new design scheme implementing a hard disk controller in a PLD with a high speed data recording rate .

介绍了在本地网网管网络中进行广域电路接口即串行端口进行Loopback测试的用途、原理和方法。

The paper introduces the use , principle and method of Loopback test in wide area circuit interface & serial port .

根据检测实际需要选择器件，确定模块与功能划分，并设计各个模块的电路接口，完成原理图与PCB版图的绘制以及硬件制作。

The author chooses the component according to the actual need , definite the module and the function , designs the electric circuit connection of each module , completes the schematic diagram and the PCB , as well as make the hardware .

FPGA逻辑设计仍然采用模块化的设计思想，在设计顶层调用各个功能子模块，功能模块有：数据采集模块、数据存储模块、PCI桥接口本地端控制模块和其他电路接口控制模块等。

The design of FPGA logic is completed under the way of modularization . We call many function modules on the top level . The function modules include data acquisition module , data storage module , PCI bridge control module and other ports control modules .

然后，根据智能IC卡话机的应用需要，从系统级到寄存器传输级（RTL）对DW8051核的外围电路接口模块进行详细规划和设计；

Afterwards , the peripheral modules have been framed and designed from system level to register-transmission-logic ( RTL ) level according to the IC card telephone application .

详细地介绍了我们设计的具有自主知识版权的NDSC-2000用户电路接口芯片的性能特点、设计原理、设计方法、设计步骤，对关键技术和工艺作了重点说明，最后给出了NDSC-2000套片的使用方法。

We have successfully designed the NDSC-2000 subscriber circuit interface chip withour own intellectual property . This article gives full details of the chip , including the perfor-mance character , design principle , design method and design procedure . And it also stresses onthe critical technique and process .

提高起重机遥控系统可靠性的控制电路接口改进设计

Design of Control Interface Circuit for Improving on Reliability of Remote Control System of Crane

介绍了自聚焦伺服型激光测微仪的控制系统的硬件电路接口及监控软件的设计与实现技术。

The design and establishment of focus servo module in the hybrid magneto-optical recording system are presented .

此外，考虑到后续功能的增加，外扩了大容量存储器，并预留多种电路接口。

In addition , the system is expanded with large-capacity memory to enlarge functions in the future .

然后介绍了不同模块间的电路接口设计，并对不同模块的工作流程进行分析。

Then describes the different modules of the circuit interface design , and different modules of workflow analysis .

重点讨论为适应高速传输模式的要求，USB20相对USB11在电路接口及其通讯机制方面的改进。

In order to adapt high speed transfer mode , The circuit interface and its communication mechanism of USB 2.0 system are improved .

给出电路接口方式、测量误差分析及实验结果曲线，液滴体积随液滴生长过程呈现良好线性关系。

Interface circuits , error analysis and experimental result graphs are presented . Excellent linearity between the drop volume and drop growth is achieved .

完成了微文氏管、四电极对微流量计和气动微阀的气路与控制电路接口设计，完成了微葡萄糖浓度传感器的电路接口设计。

The gas channels and the control circuit interface of the micro-Venturi tube , the micro-volume sensor with four pairs of electrodes and the pneumatic valves are designed .

详细介绍了机器人的控制系统方案、机械结构、硬件电路接口、软件流程、CAN总线通讯，并介绍了多自由度机器人的焊接应用。

The paper has detailedly introduced the scheme of control system , the mechanical structure , the interfaces of hardware circuit , the flow of software , communication of CAN bus , and the welding application of Multi-DOF robot .

相对于其他测长传感器而言，因为光栅尺具有精度高、响应速度快等优点，尤其是输出信号可以直接与数字电路接口且能方便地安装在X&Y平台上，很适合于本系统使用。

Compared with other linear measure sensor , grating scale has the character of high precision and response speed , output signal be interfaced to digital circuit directly and installed on the X-Y table conveniently . These merits are very fit for the system .

微结构谐振式压力传感器是通过检测其机械谐振器谐振频率的变化来实现压力测量，特点是尺寸小，精度高，稳定性好，易与数字电路接口，具有广阔的应用前景。

A microstructure resonant pressure sensor measures applied pressure by detecting change of resonant frequency of its mechanical resonator . The sensor is characterized by its very small size , high accuracy , excellent stability and convenient interfacing with digital electronics , showing broad application prospects .

有源R型温度传感器转换电路及其接口

Active - R converter of Temperature Transducer and Its Interface

给出了DSP和传感器信号调理电路的接口设计；

It applies the design of interface between DSP and sensor signal adjust circuit .

54／74HC高速CMOS逻辑电路的接口电路

Interface Circuit of a Logical Circuit for 54 / 74 HC High Speed CMOS

电路通信接口采用了USB技术，并设计了USB通信的硬件接口和软件程序。

We not only adopted USB technology in the communication interfaces of the modules , but also designed the hardware interfaces and the relevant software programs .

选择光纤通道&仲裁环拓扑连接方式，来研究高速串行SCSI接口硬件电路与接口卡设计以及接口软件的设计。

We have studied the design of hardware circuit and interface adapter of SCSI , as well as interface software .