气缸垫

介绍了一辆丰田皇冠MS132－AEPQES轿车在行驶7.6万km时，发动机气缸垫损坏，经更换新气缸垫后，出现了发动机着火后不久就熄火的故障。

After replacement of new engine cylinder head gasket instead of the broken one , a Toyota Crown car engine of 76 thousand km operating mileage encounters with the trouble of miss-fire as soon as the engine ignited .

气缸垫对机体受力状态的影响

Effect of Cylinder Head Gasket on the Stress of Engine Block

如果曲柄传动的零件已更换，则必须测量活塞在“tdc”位置的突出部分以重新确定新的气缸垫是否恰当。

If parts of the crank drive were replaced , you must determine the new cylinder-head gasket again by measuring the piston projection in " tdc " position .

发动机气缸垫失效的原因分析及其预防

The causes to the failure of the cylinder washers and preventions

在石棉气缸垫有限元分析中钢丝形状的选择

Choice of Wire Shape in FEA of Asbestos Head Gasket

接触问题有限元分析在发动机气缸垫上应用

Finite Element Analysis of Contact Problem and Its Application to Cylinder Gasket

气缸垫设计及密封问题的探讨

Discussion on Design and Sealing Function of Cylinder Head Gasket

柔性石墨气缸垫粘缸原因的研究分析

A study in the cause of sticking of flexible graphite cylinder pad

大功率柴油机新型气缸垫的开发和应用

A New Type of Cylinder Head Gasket Applied to High Performance Diesel Engines

气缸垫处有泄漏危险。

Risk of leaks at the cylinder-head gasket .

基于激光扫描的气缸垫面压测量技术

Measurement technique of the surface pressure distribution of cylinder gasket based on laser scanning

延长发动机气缸垫使用寿命的方法

Lengthening of life-span of Engine cylinder Sleeve

安装新的气缸垫。

Fit a new cylinder-head gasket .

柔性石墨气缸垫不粘缸技术研究汽车铸铁缸体焊补漏洞

Unbinding Cylinder Gasket Made by Flexible Graphite Study on welding of automobile cylinder made of cast iron

结果表明，此气缸垫的强度满足使用要求。

The results expatiated that the strength of such cylinder head gasket meet the need when being used .

气缸垫对机体受力和缸套变形影响的实验研究

Experimental study on cylinder washer 's effect on engine block stress and cylinder liner distortion for diesel engine

发动机气缸垫精确三维尺寸的获得是气缸垫质量检验及其样品反向工程的关键。

The acquirement of accurate 3D measurements of the engine cylinder gasket is the key of quality control and reverse engineering .

本文介绍一种利用激光扫描石棉纸的变形量，来测量气缸垫面压分布的技术。

The measurement technique of its surface pressure distribution is introduced in this paper , which employs a pair of laser range finders to measure the deformation of asbestos paper .

当气缸垫装在气缸体上，然后装上气缸盖以后，气缸盖螺栓就压紧软金属垫，这样结合处就完全密封了。

When the gasket is placed on the block and the head installed , tightening of the head bolts squeezes the soft metal so that the joint is effectively sealed .

介绍了一种用于发动机气缸垫及其类似的大尺寸平面薄板状零件测量的基于图像处理的激光扫描三维尺寸测量技术，并对测量试验结果进行了分析。

A laser scanning 3D measurement system based on image processing is introduced , which is used in the measurement of the engine cylinder gasket and similar plate-shaped parts , and the results of measuring experiments are analyzed .

介绍一种集弹簧、气缸和橡胶垫为一体的雷达天线座缓冲器的设计。

CUSION PLANTS The paper presents the design of an antenna pedestal buffer that combines spring , cylinder and rubber gasket into one for a radar .

Z6110型柴油机气缸盖、气缸垫接触强度分析及其算法的探讨

Cylinder Head-Cylinder Mat-Cylinder Block Contact Thermal & Mechanical Analysis and Discussion about the Method

汽车发动机气缸盖与气缸垫组合结构的有限元分析

Finite Element Analysis for Composite Structure of Cylinder Head and Cushion in Automobile Engine

建立了某柴油机机体、气缸盖、气缸垫、主轴承盖等的有限元模型；

FE models of cylinder bock , cylinder head , gasket , main bearing cups are built .

D系列柴油机气缸套变形和气缸垫密封可靠性的有限元分析

FEA of Cylinder Liner Deformation and Cylinder Gasket Leak Tightness on D Series Engine PRESSURE LEAK CALIBRATION

本文对发动机缸套-机体-垫片系统在缸盖螺栓压紧力作用下的受力进行了分析，采用轴对称模形，对D系列柴油机气缸套变形和气缸垫密封可靠性进行有限元分析。

This paper provides a stress analysis of the liner - block - gasket system under the tightening action of cylinder head bolts by the means of the axisymmetrical model , and finite element analysis of cylinder liner deformation and cylinder gasket leak tightness .

介绍了装配作业中可确保发动机气缸盖全部螺栓对气缸垫压力均等的二次紧固的特点和原理。

The features and principles of the double tightening method for cylin - der head bolts is introduced to insure the uniform pressure on cylinder gasket during assembling operation .

分析了热负荷及机械负荷对缸盖变形和结构强度的影响，查明了气缸盖火力面产生裂纹和发生冲气缸垫现象的主要原因。

The influences on deformation and strength of cylinder head by both thermal load and mechanical Joad are compared , and the causes of cylinder head cracking and the causes of gasket damage are explained .

机器加工并不能使气缸体和气缸盖平整光滑到严丝密缝，这样就要使用气缸垫。气缸体和气缸盖之间的连接必须密封以便没有燃烧的混合气体泄漏。

" The Block and head can not be machined flat and smooth enough to provide an adequate seal . Thus , gaskets are used . " The joint between the block and the head must be gas-tight so that none of the burning mixture can escape .