梭口

梭口形状对织物下机缩率的影响

The Influence of Shape of Shed on Off - loom Shrinkage of Fabric

梭口全开的时间是很重要的。

The timing of the opening of the fully open shed is important .

多梭口织机入纬率研究

Rate of Weft Insertion on Multi - section Looms

双层双梭口制织经起绒织物上机图

Draft plans for weaving warp pile fabrics by double-layer double - shed warp mounting

开口运动：将经纱分成两层，以形成梭口。

Shedding : separating the warp threads into two layers to form a shed .

梭子是从梭口的上下两层经纱之间穿过。

The shuttle passes over the lowered ends of the shed and under the raised ends .

为了便于梭子的通过，梭口必须充分开启并保持一定的静止时间。

The shed has to be sufficiently opened and remain open long enough for the shuttle passage .

高速织造梭口经纱振动特性分析

A Study on the Dynamic Characteristics of Shed Warp in the Process of Weaving with High Speed

在喷气织机上，高压气流携带纬纱穿过梭口。

In an air jet loom , high pressure air carries the filling yarn through the shed .

喷气织机后梁系统是控制经纱张力和梭口位置的重要装置。

Back rest system of loom is the main equipment of controlling the warp tension and sheld location .

纬纱会弯曲，这就要求喷气织机的梭口应大于有梭织机的梭口。

The result is that usually the warp shed must be larger than that for a shuttle loom .

另外由于在梭口中取消了障碍物，织造时使用花式纱线变得容易了。

And the weaving of fancy yams becomes much easier because the obstructions are removed from the warp shed .

织机在使用刚性剑杆时完全没有必要引导剑杆头穿越梭口。

Looms that use rigid rapiers eliminate entirely the need to assist the rapier head through the warp shed .

在两页综框平齐时，梭口被认为是闭合了。

At the time the two sheets of warp become level , the shed is said to be closed .

直至今日在我国所有生产和进口的多臂属于对称梭口。

Up to now , all the dobbies either home-made or imported are almost all of symmetrical shedding type .

分析时计及梭口两端，织口和停经架处的不同高度和前后移动，考虑到织物和经纱的刚性系数。

Different postions and movement of the shed , module of rigidity of fabric and warp were taken into account .

双剑杆系统在应用时由两只剑杆从织机的两侧进入梭口。

The double - rapier system is accepted as existing when two rapiers enter the shed from the opposite sides .

本文从织机设计和工艺角度探讨了梭口和经位置线的特性。

In this paper the author discusses from the angle of loom design the characteristics of warp shed and warp line .

当综框分别处于最高和最低位置时，梭口处于全开状态。

When the harnesses are in their maximum up and down positions , the shed is said to be fully opened .

结果表明，发生断头最频繁的区域是前梭口区和综框区，其中综框区最多。

It is found that the front shed area and the heald frame area are susceptible to heavy breakages , especially the latte area .

多层多梭口织造法很适合于正则角联锁结构的织造，不仅可以成倍地提高生产效率，而且对经纱的损伤大大降低。

The weaving efficiency of multi-layers and multi-sheds weaving method could be much higher and weaving friction to warp could be much lower than before .

纹板上的孔允许相应的竖钩提升，这就确定了在构成梭口时，哪些经纱应该提起。

The holes in the card permit the lifting of hooks on the machine that determine which warp yarns are to be raised in forming the shed .

剑杆仅仅是这样一个装置，它由金属或复合材料制成，在其头部有一个附件携带纬纱穿过梭口。

A rapier is merely a device made of metal or a composite material with an attachment on the end to carry the filling yarn through the shed .

开口运动是将经纱分成上下两层形成梭口，使梭子从其间通过。

The shedding motion separates the warp ends into an upper and a lower system of threads to permit the shuttle to pass through the space that has been formed .

纬纱前端的速度低于后部的速度，纬纱会弯曲，这就要求喷气织机的梭口应大于有梭织机的梭口。

The front moves slower than the rear and the yarn buckles . The result is that usually the warp shed must be larger than that for a shuttle loom .

如果减少给梭子加速用的时间，而且梭子穿过梭口的时间也能减少，织机便可以以较高的速度运转。

If less time could be spent accelerating the shuttle , and the transit time of the shuttle through the shed could be reduced , higher loom speeds could be obtained .

经纱以一定的方式被穿在综丝眼中，通过织机开口机构的驱动上下运动，形成梭口。

The warp ends are drawn through heddle eyes in the correct manner and in the turning-over of the crank shaft of the loom , a shed is formed with each turn .

在大多数情况下，当钢筘前面的梭口尚小于梭子大小（指横截面）时，便可能使梭子进入梭口。

In most cases it is possible to allow the shuttle to enter the shed before the opening of the shed in front of the reed is as large as the shuttle size .

为了顺利开发一个梭口中引入两根纬纱形成的横条织物，对产品的技术规格与性能特点进行了分析，并优选原料，优化配置织部工艺。

To produce strip fabric which two wefts in one shed , technology specification and property speciality of products were analyzed , raw materials were optimized , and weaving processing were optimized too .

为了提高产品质量，通过改变边组织、调整梭口闭合时间、调节张力片张力等措施，使入库一等品率达98.8%。

To enhance product quality , measures of changing selvage stitch , adjusting shed closing time and tension bar were done , and the first grade rate in storage can reach to 98.8 % .