推挽输出
- 网络push-pull;push pull;Push Pull Output
-
该放大器利用工作在亚阈值区的CMOS基准源,在此基础上运用了PMOS差分输入级,以及CMOS推挽输出级结构。
The circuit was based on CMOS reference operating in subthreshold region , using PMOS differential input and push-pull CMOS output stage mode .
-
用SPICEⅡ对设计电路的计算机模拟表明,具有推挽输出结构的三值TTL电路具有较强的驱动能力及较快的工作速度。
Computer simulation of the circuits designed with SPICE ⅱ shows that the ternary TTL circuits with push-pull output construction have better driving ability .
-
输出级采用了AB类推挽输出以获得高的输出摆幅。
Output stage is a class AB to obtain the output high swing .
-
用开关信号理论指导具有推挽输出结构的三值TTL电路的设计
Design of TTL Circuits with Push - pull Output Construction by Means of Switch - signal Theory
-
本文分析了以电阻为负载的传统三值TTL反相器的缺点,借鉴二值TTL推挽输出级的结构,设计了三值TTL电路的推挽输出级。
In this paper , the drawback of conventional ternary TTL inverter with resistor as its load is analysed , and the push-pull output construction of ternary TTL circuit is designed by referring to its binary counterpart .
-
本文分析了具有推挽输出结构的三值TTL的输出级电路,提出了相应的开关模型,借助开关一信号理论,讨论了具有推挽输出结构的三值TTL电路的元件级逻辑设计。
In this paper , the ternary TTL output circuit with push-pull output construction has been analysed , and its switch model is presented . By means of the theory of switch-signal . the logic design of the ternary TTL circuits with push-pull construction at element level is discussed .
-
实验证明,所搭建的系统,可以很好地实现双丝的推挽式输出,焊接过程稳定,焊缝成形美观。
The experiment proves the system could realize the push-pull output of double-wire . The welding process is stable and the welding molding is good .
-
同时运用ClassAB推挽电路作输出级,获得高驱动能力和低谐波失真。
Meanwhile , a class AB output stage is also developed to ensure large dynamic range , strong driving capability and low harmonic distortion .
-
第二,推挽A级放大器输出阶段将拥有固有拒绝电源纹波和噪声。
Second , a push-pull class A amplifier output stage will have inherent rejection of power supply ripple and noise .
-
现代运算放大器有某种方式的推挽式的输出级,许多也是不对称的,并且某一方向的压摆率有比其它方向的有更大的倾向。
While all modern op amps have push-pull OUTPUT stages of some sort , many are still asymmetrical , and have a greater slew rate in one direction than the other .
-
通过对三种电路方案的比较,ZVS推挽谐振电路具有输出电压稳定、效率高的特点,是模板化航空静止变流器直流环节的优选拓扑方案之一。
Through the comparison of three schemes , the ZVS push-pull resonant converter is one of the best DC link topology for the modularization aviation static converter .
-
通过一对波形完全相同、相位差为180°的SPWM信号进行门极驱动,可在推挽式逆变器的输出端得到一个合成的正弦电压源。
With gates driven by a pair of SPWM signals , SPWM positive and SPWM negative , which have the same waveforms but 180 ° phase shift , a voltage source within full sine wave is composed at the output terminal of a push-pull inverter .
-
本文在电源主电路方面选用推挽电路,其输出整流方面采用倍流整流方式,可以拓宽电源的应用范围和降低变压器的制造难度,实现高效率的电源。
Based on the push-pull topology , using double-current rectification in secondary part , it can wide the appliance scope , decrease the difficulty of manufacturing transformers and achieve high efficiency converters .