工艺试验

文章介绍了上述石油系统（CNPC）煤层气钻井现状及煤层气小井眼钻井技术研究和勘探性工艺试验情况。

In this paper , the actual drilling situation for coalbed gas and the situation of slim hole drilling technique and technological test for coalbed gas by CNPC is presented .

通过对Se75射源特性的分析和工艺试验，证明Se75射源在小径管射线透照中的具有较高的灵敏度和较好的宽容度，并探讨其射线探伤的可行性和应用前景。

Through analysis and technological test of the characteristics of Se 75 radiation source , it is proved that Se 75 radiation source havs relatively high sensitivity and good tolerance and the feasibility and application future of Se 75 radiation source used in RT are studied .

1（1/4）Cr&（1/2）Mo耐热钢焊接工艺试验

Welding Technique Tests of 1 ( 1 / 4 ) Cr-1 / 2Mo Heat-resistant Steel

通过选择接触反应钎焊的中间层成分，采用Si为中间层介质进行钎焊工艺试验。

The interlayer for contact reactive brazing was chosen , and the brazing technical experiments using Si interlayer were carried out .

对M3滚刀进行了物理气相沉积（PVD）工艺试验。

The technology test of PVD is used on M3 hob .

对未掺杂单晶硅和掺杂N型硅进行了电火花加工工艺试验，得出了掺杂N型硅有很好的微细电火花加工性能的结论。

And draws a conclusion that doped N type monocrystal silicon is quite fit for micro EDM , while a non doped one isn 't by a lot of EDM experiments .

MDF管道与搅拌联合施胶新工艺试验

An Experiment on the New Gluing Technology of the Combination of Blow-Line and Agitation for the

通过一系列的焊接工艺试验，对输送H2S介质的服役管道焊接接头进行了全面的评价，最终确定了输送H2S介质压力管道维修的焊接工艺参数。

The comprehensive evaluation of welded joints in the transmission medium H2S service pipe was conducted through a series of welding experiments .

LY12法兰盘整体加压挤压铸造工艺试验

LY 12 Flange in Squeezing Casting

6005A铝合金大直径圆铸锭生产技术圆钢锭浇铸工艺试验

Process technology for 6005A aluminium-alloy large-size round ingot

秦沈客运专线24m箱梁制造工艺试验

Tests of Precasting Procedures for 24-m Box Girders to be Used on Qinhuangdao & Shenyang Special Lines of Passenger Trains

本文在可溶性还原染料对锦纶的染色工艺试验的基础上，着重对防光脆化问题进行了研讨。试验表明：印地素金黄IRK和妃红IR是促使锦纶纤维光化降解的光敏染料。

On the Basis of an experiment on the dyeing technology of solubilized vat dyes on chinlon , the light-degradation of the fibre is emphatically discussed .

本文还对淬火45钢进行了LFW工艺试验。

On the other hand , the experiments with the quenched 45 steel were done under different LFW parameters .

以甲苯氯化副产物HCl作为氧化反应原料，采用γ-Al2O3负载铬活性组分的催化剂，在固定床反应器中进行氯化氢氧化制氯气工艺试验。

With hydrogen chloride produced by chlorination of toluene as raw material , the experiment of hydrogen chloride oxidation was carried out in a fixed-bed reactor with catalyst of γ - Al_2O_3 laden chromium .

结果表明：对半固态AZ91D镁合金组织结构的影响主次顺序为：搅拌速度、静置时间、浇注温度、搅拌时间；通过试验得到了最优的工艺试验参数：搅拌速度500r/min；

The results show that stirring speed is the main factor to influence the semisolid magnesium alloy microstructure , the optimum parameters are obtained by orthogonal experiment .

LTC-9560多功能流态床炉工艺试验

Technical Test in The LTC-9560 Multi-Purpose Fluid Bed Furnace

介绍了正火处理的Cr-Mo钢焊接接头性能的工艺试验情况，重点探讨了焊接接头抗拉强度和低温冲击性能的影响因素。

This technology test presentation is about procedure test of weld joint property of Cr-Mo steel through normalizing heat treatment , including the tensile strength and impact toughness under low temperature .

通过LF6/LD10铝合金搅拌摩擦焊（FSW）的工艺试验研究，分析了工艺参数对其接头性能的影响。

Mechanical properties of welded joint of LF6 / LD10 aluminum alloy by FSW were studied . The results showed that welding process parameters have an essential effect on mechanical properties of LF6 / LD10 aluminum alloy joint .

采用双变供氧制度和新的渣料加入量计算法，在浦钢公司30t氧气顶吹转炉上进行了新的冶炼工艺试验研究。

In 30t oxygen top-blown converter of Pudong Iron and Steel Company , Ltd. the new technology experiment has been carried out with double changeable oxygen-supplying system and new calculation methods of slag materials .

采用国产高分子凝聚剂（TXD-63），在万吨级的SBR工业装置上，对SBR1712胶乳进行了TXD-63-硫酸凝聚工艺试验。

The coagulation test of SBR-1712 latex , by using the TXD-63 ( polymeric flocculant ) and sulfuric acid system was carried out on a 10 kt SBR commercial plant .

采用湿摩擦牢度提升剂FCG-10对织物进行固色，工艺试验及生产实践结果表明，能一定程度地提高织物摩擦牢度。

The improver FCG-10 was applied to fixing during dyeing . Trials and productions showed that the wet rubbing fastness of dark fabric was increased in certain degree with FCG-10 .

通过测试窑体的部分性能和进行杉松中板工艺试验，考察安装在贵州省林机厂的某HMA型电加热远红外木材干燥窑的构造特征和工艺效果。

The structural characteristics and technological effect of HMA electric far infrared ray drying kiln , which was built at Guizhou Forest Machinery Factory , were observed by means of some of property of the kiln and technologic on drying Tsuga chinensis and Pinus massoniana planks .

工艺试验表明，带接箍油管另一端加工螺纹时，其接箍对螺纹质量基本无影响，其检验项目锥度、螺距、齿高、紧密距、L4长度均在公差允许范围内。

Relevant process testing showed that when threading the non-coupled end of a coupled tubing , thread quality was negatively affected little by the coupling , and that all the items inspected , namely taper , pitch , tooth height , standoff and L4 were within the specific tolerances .

从理论上探讨了利用RH-KTB深脱碳时进行深脱氮的可能性，并结合武钢二炼钢RH-KTB深脱氮工艺试验情况，分析了影响深脱氮的因素。

The present paper discusses the possibility of deep denitrification in the process of deep decarbonization by RH-KTB in theory and analyzes the factors affecting deep denitrification on the basis of experiments on the deep denitrification by the RH-KTB process carried out in No. 2 Steel-making Plant of WISCO .

高压气淬炉H3636-6bar的验收及工艺试验

Acceptance and Process Testing on Furnace for High Pressure Gas Quenching

辊套热处理工艺试验与改进

Test and Improvement on Heat Treatment Technique of The Roller Jacket

工艺试验参数模糊集值统计推理预测

Prediction of Statistical Inference for Fuzzy Set Values of Test Parameters

硫化汞锑矿汞锑分离降铬工艺试验研究

Study on Chromium-dropping Technology in Hg-Sb Separation Process of Livingstonite Ore

单缸柴油机油泵凸轮的耐磨工艺试验分析

Experiment Analysis of Wear Resistance oil Pump Cam of Diesel Engine

通氨滴醇软氮化工艺试验

Testing of Tufftriding Process With Passing Ammonia and Dripping Ethanol