套合

GPS数据与TM卫星影象套合误差小于一个象元；

The error which GPS datum supposed TM images is less than one pixel .

更新调查矢量数据与第二次土地调查DOM套合方法探讨

Method for Data Fitting Between Vector of Updated Survey and DOM of the Second Land Investigation

尾轴管橡胶衬套嵌套三维Kriging方法中的变异函数套合

Fitting rubber liner for stern tube Nested Overlap of Variograms in 3D Kriging

元素浓集中心的空间套合程度最高的是Pb、Zn、Ag，其次为Cu和Sn。

The most associated elements concentrations are the Pb , Zn and Ag , with the Cu and Sn coming next to it .

根据胶连接的经验公式和ANSYS分析结果确定了胶连接的套合长度，并对胶的剪切强度进行了校核。

Based on the glue connection experience formula and ANSYS analysis results , the best length of connection , and the shear strength of glue .

其水系沉积物异常强度高、面积大、元素套合好，Ag、Pb、Zn、Mn等单元素异常中心与矿床的产出部位一致。

The characteristic of its stream sediment anomaly is high anomaly intensity , large area and good identity of concentration centres for elements . The concentration centres of Ag , Pb , Zn and Mn etc. are identical to the occurrence of the deposit in space .

以往的立体地质图多是利用数字地形模型（DEM）对二维数字地质图进行了Z轴方向的拓展，然后再与数字正射影像（DOM）进行套合，形成了所谓的2.5维模型。

The previous three-dimensional geological maps are the expansion of the two-dimensional digital geological map in Z-axis on the use of digital terrain model ( DEM ), And then with Digital Orthophoto ( DOM ) overlay , which formed the so-called " 2.5D " model .

在很多情况下，需要用DOM和DLG的叠加配准：检查DLG精度，DOM套合DLG进行外业调绘，DLG与DOM叠加生成复合地形图。

There are several situations where the registration of DLG and DOM is wanted : DLG precision check , a combination of DLG and DOM for field mapping , congruence of DLG and DOM to obtain multiplex relief map .

土壤水分空间变异的套合结构模型及区域信息估值

Combination structure model of soil moisture spatial variability and regional information estimation

不同材料球壳套合联结的弹塑性解

The Elastoplastic Solution of Combined Spherical Shells with Different Materials

并提出了油气藏的套合异常模式。

An overlaping model is proposed for the exploration of oil reservoirs .

套合后整理清洗干净，在轴承中注入50%-70%润滑脂。

After clearing , you should put lubricant at50 percent to70 percent .

气井油套合采时井底流压的计算方法

Method of wellbore pressure calculation for tubing-casing production system of gas wells

螺旋桨液压套合过盈量的可靠性设计

The Over Surplus Quantity Reliability Design of Hydraulic Pressure Sheath Screw Propeller

四环是互相套合的，是要均衡发展的。

The four factors are interrelated and develop in equilibrium .

舵柄与舵杆无键液压套合连接推入量计算

The Calculation of Pull-up on Keyless Oil Shrink Fitting for Tiller and Rudder Stock

最后一次显影才显出套合图象。

Final development reveals a combined image .

多因素套合分析法在辽河群地层区铅锌矿成矿预测中的应用

Application of multifactor overlap analysis in the metallogenic prognosis for lead-zinc ore in Liaohe Group

关于套合零件装配协调问题的探讨

Discussion about Assembling Coordination of Nest_Type Parts

大比例尺地形图的套合修测

The Adjustment Revise of Large-scale Topographical Maps

江汉平原典型区农田土壤全氮空间变异的多尺度套合

Multi-scaled nesting of spatial variability of soil total nitrogen in farmland soils typical of Jianghan Plain

越野汽车差速器同步锁止机构套合器齿形加工设计同步码的完全化构造方法

Machining Mechanism of Dog Clutch for Synchronous Differential Lock of Off-road Vehicle Completion of Synchronous Codes

增给内容的基本要求是：增给部分必须与旧图套合准确。

The essential requirement for addition is that they will be in register with the old work .

介绍了舵柄与舵杆无键液压套合工艺的优点。

This article describes the advantages of the fitting of keyless tiller with rudder stock by oil shrink method .

两个垂直方向的稳健变异函数套合后进行克立格估值的最优等值线图与模型模拟图反映了实际的水盐含量。

Kriging gaging former plots and classic isoline maps of two vertical direction combination structure model reflect actual water-salt content .

在区域化探中必须应用三层套合方差分析对样品的采样误差和分析误差进行统计分析。

In local chemical exploration , the variance analysis of three-stage-model must be applied to estimate analytical uncertainly and sample-collecting error .

在笼统正注井、笼统反注井、油套合注井、分层配注井中测量注入剖面。

The injection profiles are measured in the general positive injector , general negative injector , multilayer injector and separated-layer injector .

本实用新型公开一种多节式伞中棒，由二节以上伞节套合而成。

The utility model discloses a multi-section type umbrella stick , formed by more than two umbrella sections which are sleeved .

结果实验表明，镍钛记忆合金套合式交锁髓内钉在抗弯曲方面与钢板无显著性差异，优于ender's钉；

Results The bending strength of Ni-Ti En was not significantly different from that of the plate and better than ender 's nail ;

工作成果表明，其重复定位精度、所制板图的套合精度以及图形质量均达到国内先进水平。

The results show that its repetitive positioning accuracy , overlap accuracy of masks and quality of masks have reached advanced level in China .