合金板

La-Mo合金板轧制工艺及组织性能研究

Research on Rolling Technology , Microstructure and Properties of La-Mo Alloy Plate

通过大量仿真实验得出了铅合金板超声铸轧的最佳工艺参数，最终通过实验研究了超声波铸轧铅合金板的各项性能。

We got the best process parameters of Lead alloy plate ultrasonic casting through a lot of simulation and finally studied the performance of the ultrasonic casting lead alloy plate by experiments .

大多数太阳能热水器使用大片的涂成黑色的铝板或合金板来吸收太阳的热量。

Most solar heating systems use large aluminum or alloy sheets , painted black to absorb the sun 's heat .

本文对受拉伸载荷的铝合金板被强连续波CO2激光照射时的热机械响应进行了报导。

Thermomechanical response of Al plates under tension to high energy CW CO2 laser radiation is discussed .

Zr-4合金板α相高温区轧制的织构演化

Texture Evolution of Zircaloy-4 Plate Rolled at High α Temperature

轧制温度对Zr-4合金板织构的影响

Effect of Rolling Temperature on the Textures of Zircaloy-4 Plate

Al-Zn-Mg合金板淬火时效工艺研究

Research of quenching and aging institution for an Al-Zn-Mg alloy sheet

用ODF图的诠释图分析铸轧3004铝合金板织构

Analysis of Texture of 3004 Alloy Sheet Produced from Continous Casting Sheet by Explanation ODF Figure of Cubic Materials

AZ31镁合金板热拉深成形工艺研究

Research on the Thermal Deep-Drawing Process of ( AZ31 ) Magnesium Alloy Sheets

用反极图和织构取向因子等方法研究了经300～980℃轧制75%的Zr－4合金板的织构。

The textures of Zircaloy-4 plates rolled at temperatures from 300 ℃ to 980 ℃ were studied by employing the techniques of inverse pole figure and texture orientation factor .

用高温应变计和热偶计等诊断技术，研究连续波氧碘化学激光（CW／COIL）与铝合金板作用产生的激光热应力。

The laser thermal stress induced in the aluminum alloy plate irradiated by CW / COIL were investigated by high temperature straingauge and thermocouple gauge and other diagnostic techniques in this paper .

TZM合金板、棒材的研制和应用

The research and application of TZM alloy

对厚度为3mm的LF2铝合金板成功地进行了搅拌摩擦连接。

The aluminum alloy LF 2 ( 3 mm thick ) was successfully friction-stir welded .

为分析E－400铝合金板翅换热器A流道的爆破失效原因，对A流道中的残留物质进行了各种化学和X射线分析，进行了A流道实物模拟爆破试验。

In order to analyze the reason of exploding occurred in the stream A of E-400 Al-Alloy Plate-Fin Heat Exchanger , a simulated exploding experiment is carried out and various chemical and X-ray analysis for substances obtained fron the stream A are made .

采用定向凝固方法制备了Fe65%Si实验合金板，并进行了金相观察、X射线衍射分析、EBSD分析和磁性测定。

Test plate of Fe 6 5 % Si alloy is prepared by directional solidification , which is studied by optical microscope observation , X ray diffraction analysis , EBSD investigation and magnetic determination .

铅蓄电池Pb-Sr合金板栅材料电化学性能

Study of Electrochemical Properties of Pb-Sr Alloys for Lead-acid Batteries

利用初始单系滑移模型和{123}〈634〉织构组分体积分数可以快速而准确地计算出3104铝合金板的应变比（r）值，并兼顾到非织构因素的影响。

According to the volume fraction of the { 123 } 〈 634 〉 texture , the r value of the 3104 aluminum sheets was calculated rapidly and accurately based on the initial single slip model , while some other effect factors beside texture were also included .

以深冲铝板R值的在线检测为应用背景，塑性变形滑移系开动的过程为出发点，分析了初始滑移系选取的方式，并计算了不同取向3104铝合金板的初始R值。

In consideration on the on-line R-value measurement of aluminum deep drawing sheets , the selection of initial slip systems was analyzed according to the activation process of the slip systems during plastic deformation . Initial R values of the 3104 aluminum sheet in different directions were calculated .

结果表明，冷轧变形65%，经540℃／2h退火，可以显著提高Zr－4合金板的织构强化效果。

The results show that , the deformation during cold rolling reaches 65 % , after annealing at 540 ℃ for 2 hours the strengthening effect of the texture of Zr-4 alloy plates can be remarkably increased .

防盗盖用3003S合金板带材生产工艺研究

Study on production process of 3003S aluminium alloy plates strips for anti-imitating lid

在材料模型的基础上，利用DEFORM有限元软件对AZ31变形镁合金板温拉深笔记本外壳实验做了模拟。

In the base of the flow stress model of AZ31 , finite element analysis software DEFORM was used to research the drawing of the notebook PC case with magnesium alloy AZ31 sheet .

铅锑和铅锡合金板栅表面钝化层由Pb、铅氧化物、PbSO4、锑氧化物或锡氧化物构成。

In addition , the forms and positions of tin and antimony in the passive layer were investigated . The results showed that the passive layer developed on the Pb-Sn and Pb-Sb grids contained Pb , Pb oxides , PbSO_4 , Sb oxides or Sn oxides as well .

铝合金板LY12～M12的实验研究表明：随着塑性予应变的增加，将依次出现各向同性强化、运动强化以及组合强化。

A study of aluminium alloy sheet shows that , the isotropic hardening , the kinematic hardening and the combinative hardening would occur successively as the plastic prestrain increasing .

本课题是郑州大学与美国通用汽车公司合作的美国通用联合基金项目JoiningofDissimilarMaterialswithCrash-ToughenedAdhesives的一部分，其目的是探索镁合金板料在汽车工业中应用的可能性。

This paper is a part of GM Joint Funding Project " Joining of Dissimilar Materials with Crash-Toughened Adhesives " carried out by Zhengzhou University and General Motors Corporation , which aims to explore the possibility of applying magnesium alloy in the automobile industry .

对ME20M镁合金板料进行了热拉深成形性能实验与数值模拟。

The experiment and numerical simulation of hot deep drawing forming properties of ME20M magnesium alloy sheet are researched in this paper .

本文是针对320C铝合金板翅式机油换热器在性能测试过程中，焊缝的断裂失效而进行的。

In this dissertation , based on the fracture failure of performance tests of 320C Al alloy heat exchanger , several reasons were analyzed .

本文对凝固过程中采用的缩孔缩松判据函数进行了评述，并结合真空精密铸造IN738合金板类铸件，验证了Niyama判据函数G／R1／2在镍基合金铸件中的应用。

Abstract The shrinkage porosity functions used in the solidification process were reviewed in this paper . By using vaccum investment casting of IN 738 plate casting , the applicability of Niyama function G / R 1 / 2 to the Ni based alloy has been proved .

采用铅锑镉合金板栅的利弊

Advantages and disadvantages of Pb-Sb-Cd grid alloy used for lead-acid batteries

转动结构在铜合金板带残余应力及变形检测中的应用

Rotating-Structure Application in Residual Stress and Deflection Detecting of Copper-Alloy Strip

镁合金板料温冲压成形数值模拟技术

Numerical Simulation Technology of the Warm Pressing of Magnesium Alloy Sheet