十字头

这是机器夹头或十字头会产生一种坚韧的，不可抗拒的动作。

It is a relentless or irresistible action of the machine grips or crosshead .

十字头的联杆器挤带有指示针和电线模具。

The crosshead also holds the guide-tip and the wire die .

介绍了Φ400mm轧辊传动端十字头磨损后焊接修补的工艺，修复后轧辊的轧制量能达到36万t。

The weld repair technology was introduced for crosshead of driven end of Φ 400mm roll . The rolling amount can reach 3.6 × 10 ~ 4t after the roll repaired .

液压支架推杆十字头万向接的有限元分析

Stress-Strain Analysis for Cross Connector of Powered Supports with Finite Element Method

完成的曲轴箱和安装的是十字头指南。

The crankcases are finished and mounted as are the crosshead guides .

十字头塑件无顶出侧向分级抽芯注射模设计

Design of Injection Mold with Non-Ejector Side Grading Drawing-Core for Crosshead Plastic Parts

二冲程柴油机十字头轴承油槽优化研究

Research on Crosshead Bearing Oil Groove in Two-Stroke Engine

高压往复式氢气压缩机十字头销断裂原因分析与对策

Analysis of crosshead pin cracking failure of high-pressure reciprocating hydrogen compressor and Countermeasures

十字头衬瓦并未牢固浇铸，因此可进行更换。

The crosshead liners are not rigidly cast , and can thus be replaced .

十字头轴承早期损坏的原因分析与措施

Analysis of Cause and Taking Measures for Early Failure of Bearings of Cross Heads

活塞式压缩机十字头与滑道配合间隙测量实践

Clearance Measurement Between the Spider and the Sliding Road in the Piston Type Compressor

往复式压缩机十字头故障分析与处理

Crosshead Malfunction Analysis & Maintaining for Reciprocating Compressor

使用两个沉头十字头螺钉将专用工具辅助定心工具固定到曲轴箱上。

Secure special tool centring aid to the crankcase using two countersunk crosshead screws .

活塞固定在十字头中。

The plunger is clamped into the crosshead .

低速二冲程柴油机十字头轴承的龟裂及管理措施

Simple Statement of Craze and Manage Measures to Cross Bearing of Two-cycle Diesel Engine

压缩机十字头销断裂失效分析及预防

Failure Analysis of the Compressor Crosshead Bolt

异型十字头联轴器特性分析

Analysis of Properties of Varied Cross Coupling

十字头润滑油泵传动杆

Driving lever for crosshead lubricating pump

应用正交试验法解决高压泵十字头铜套过热抱死问题

Solution for Overheat Lock Breaking of Crosshead Copper Sleeve in High Pressure Pump by Orthogonal Test Method

天然气压缩机十字头摩擦层和本体的选材及结合形式

Material selection and bonding pattern of friction layer and body of crosshead on gas on gas compressor

十字头润滑油泵套筒

Liner for crosshead lubricating pump

6HF/3大型往复压缩机连杆与十字头销烧蚀故障分析

Analysis on ablation failure of connecting rod and crosshead in large 6HF / 3 type reciprocating compressor

加氢裂化新氢压缩机连杆小头衬套与十字头销烧损原因分析

Analysis of Small End Bushing and Crosshead Pin Failure of Fresh Hydrogen Compressor Connecting Rod in Hydrocracking Unit

十字头连接活塞杆和往复式发动机连杆的横杆

A beam that connects the piston rod to the connecting rod of a reciprocating engine . back-side-crank pumping unit

崎岖的设计，这蒸汽机是不寻常的结合，职能十字头，引导和支持在缸一套单一的栏目。

The rugged design of this steam engine is unusual in combining the functions of crosshead guide and cylinder support in a single set of columns .

由压缩机的结构和工作原理可知，压缩机的振动信号基本上都是非平稳信号，如气阀，十字头、活塞等振动信号。

The vibration signals of reciprocating compressor are basically non-balanced from its configuration and work principle , such as the vibration signals of air-valve , crosshead and piston .

阐述了4L-20/9-Ⅱ型焦炉煤气压缩机十字头滑道频繁烧研的过程，并对烧研原因进行了认真分析。

The burnout and wear procedure of cross slide way of 4L-20 / 9-II coke-oven gas compressor was presented and the burnout and wear causes were seriously analyzed .

另外，活塞一般是靠十字头与连杆连接的，十字头沿着固定于机身上的滑板作往复运动。

In addition , the piston is generally with the connecting rod connected by a powerful , powerful fixed in the fuselage along the board for reciprocating motion .

一种新十字头连接结构，由活塞杆、球面垫圈、十字头、十字头销和连杆组成。

The utility model relates to a novel crosshead connecting structure which is composed of a cylinder rod , a spherical washer , a crosshead , a cross pin and a connecting rod ;

接着做出约束模态和自由模态分析，计算十字头的固有频率及其对应的振型，最终对十字头的结构合理性做出判断和评价，为进一步的结构优化提供有价值的参考。

Then constraint mode and free modal analysis is made , calculation of natural frequency and the corresponding crosshead the vibration model , ultimately for the structure of the crosshead judge rationality and evaluation .