冷却方式

分析表明，轧后冷却方式对获得细小弥散析出的V（C、N）是很重要的。

It is considered that the cooling method after rolling is very important for obtaining the fine precipitates of V ( C , N ) .

冷却方式对Fe3Al金属间化合物组织和性能影响的研究

The Influence of Cooling Method to the Organizations and Properties of Fe_3Al Intermetallic Compound

最后探讨了在强制风冷情况下探照灯内的温度场和流场分布。本章内容为提高LED红外探照灯的可靠性和冷却方式设计提供了理论依据。

Moreover , the temperature and flow field distribution under forced ventilation are also discussed .

研制成功了一种采用新型冷却方式的连续CO2激光器。

A heat-PiPe Cooled CW CO_2 laser is reported here in this paper .

不同冷却方式下SiCp/356Al复合材料的热应力分析

Thermal Stress Analysis of SiC_p / 356Al Composite Under Different Cooling

冷却方式对Y2O3-ZrO3陶瓷相变及力学性能的影响

Effect of cooling mode on transformation and mechanical properties of y_2o_3-zro_2 ceramics

针对H型钢轧制中的一些问题，设计了H型钢在线控冷装置。此装置采用气雾冷却方式，着重对H型钢R部进行快速冷却，冷速达100℃/s以上。

An on-line cooling device for H-beam was built with mist cooling instead of air cooling which is effective for cooling R-part at a speed of more than 100 ℃ / s.

提出了CSP衔接区坯料的冷却方式，并给出了相应的模型。

Finally , the cooling pattern of the slabs in the linking region of CSP is put forward , and the corresponding model presented .

研究了常压烧结Y2O3-ZrO2陶瓷不同冷却方式对其力学性能及t&m相变的影响。

Effect of four different cooling modes on t & m transformation and mechanical properties of Y_2O_3-ZrO_2 ceramics were studied .

讨论了混炼剪切力、成型冷却方式和UHMWPE熔体粘度对材料力学性能的影响。

The influences of shear stress at mixing , cooling system in molding and melt viscosity of UHMWPE on mechanical properties of composites are discussed .

热处理冷却方式对Al-Zn-In合金电化学性能的影响

Effect of cooling methods after heat-treatment on electrochemical performance of Al-Zn-In alloy

冷却方式对Zn-Cu包晶合金微观组织的影响

Effects of Cooling Ways on Microstructure of Zn-Cu Peritectic Alloy

500kV变压器的冷却方式

The Cooling Method of 500 kV Transformer

不同冷却方式对Er~（3+）/Yb~（3+）共掺BaF2粉末上转换发光效率的影响

Effect of Different Cooling Techniques on Up-converted Fluorescence Efficiency of Er ~ ( 3 + ) / Yb ~ ( 3 + ) Co-doped BaF_2 Powder

本文采用不同烧成方式及不同冷却方式，对不同配料的高C3S水泥生料进行了实验室烧制。

It is adopted different burning and cooling means for different high-C3S cement raw meal to calcine clinker in the lab.

汽轮机快速冷却方式在700MW机组的综合应用

Synthesis Application of Turbine Force Cooling Mode in 700 MW Unit

该水泥的最佳烧成制度为：烧成温度为1380℃，保温时间为60min，冷却方式为自然冷却；

The optimum burning system is : the cooling mode is natural cooling mode ; the burning temperature 1 ? 380 ?

采用高功率LD阵列作为泵浦源，Yb激光晶体或陶瓷作为激光材料可以带来更高的系统效率和可靠性同时满足宽带传输的需要，采用主动的冷却方式可以得到更高的重复频率。

With high power LD array as its pump recourse and Yb-dope laser crystal or ceramic as its laser material , the drive can achieve higher system efficiency and dependability ; meanwhile fill the need of broad band transmission .

改进铸模和冷却方式获得的平板铸锭晶粒较小，柱状晶明显，富Nd相较薄，但某些小区域仍有团絮状的富Nd相。

The grains of flat ingots got by improving cast mold and ways of cooling are relatively small , the pillar-like grains are obvious , and the Nd-rich phases are relatively thin , but there are still group floc-like Nd-rich phases in some small regions .

通过进一步的分析比较，初步确定了SCQ磁体的冷却方式及满足SCQ磁体冷却条件下的氦过冷换热器的设计参数。

In the end determined cooling scheme for the SCQ magnets and design parameters of the subcooler .

冷却方式对Mg-Nd-Pr合金的显微组织与物相构成的影响

Effect of Cooling Method on the Microstructure and Phase Composition of Mg-Nd-Pr Alloy

研究了热处理冷却方式对AB5型储氢合金电化学性能的影响。

Effects of cooling method after heat-treatment on electrochemical performance of AB5-type hydrogen storage alloy are studied .

针对中国先进研究堆（CARR）冷中子源的技术难点，研究采用国际上尚无先例的带助冷冷包结构及带助冷两相热虹吸自然循环冷却方式的可行性。

The feasibility of the new cooling method in the world , two-phase thermo-siphon with auxiliary cooling , was studied in order to resolving the difficulties in the design of China Advanced Research Reactor ( CARR ) cold neutron source ( CNS ) .

综合考虑了最高受热温度和冷却方式，对普通混凝土（C35）与高强混凝土（C60）高温后抗压强度及高温粘结性能差异进行比较研究。

The article compared the difference between normal concrete ( C35 ) and high-strengh concrete ( C60 ) in compressive strength and bond properties with the influence of the highest temperature and cooling methods .

为尽早开发国内24kV级大型汽轮发电机，提出了采用蒸发冷却方式的技术路线。

In order to develop the first inland 24 kV rated voltage turbogenerator , this paper proposes to adopt an evaporative cooling method to realize it .

并确定聚光集热子系统中传热工质HTF的温度和流量。其次，模拟分析了气象条件、HTF温度和冷却方式对系统性能的影响。

The inlet and outlet temperature and mass flow rate of HTF in solar field were determined . Secondly , the influences of weather conditions , temperature of HTF and cooling methods to system performance were simulated and analyzed .

结合生产，对S-136淬硬钢高速铣削工艺的刀具选择、冷却方式、进给路线进行了分析。

Choice of cutting tool , cooling manner and feed path in high speed milling S-136 hardened stainless tool steel were analyzed , based on a S-136 die production .

对于铸态Mg-Al-Nd镁合金，固溶处理后的冷却方式对形成过饱和的固溶体组织有很大的影响；合金的力学性能随着冷却时间的延长呈下降的趋势。

For the as-cast Mg-Al-Nd magnesium alloy , the cooling mold after solution treatment had the effect on the microstructure of oversaturated solid-solution , and the mechanical properties of alloy was dropped along with the holding time prolonged .

汽轮机停机后快速冷却方式的分析

Analysis of quickly Cooling Means for the Turbine after being Stopped

西北地区大型汽轮机冷却方式研究

Researches on Cooling Modes for Large-Sized Steam Turbines in Northwest China