结晶器

改进的PSO及其在结晶器液位控制中的应用

Improved PSO and its application in crystallizer liquid level control system

结晶器液面计棒状~（137）Cs源的设计

Design of the rod - like ￣() 137cs source used in the crystallizer liquidometer

对结晶器钢水液位控制采用了基于专家知识的智能PID模糊复合控制策略。

Comparison and research on strategy of mold level control are made .

连铸结晶器液压振动系统的H∞混合灵敏度控制与仿真

H_ ∞ Mixed Sensitivity Control and Simulation for Hydraulic Oscillating Systems of Continuous Casting Mould

应用FEM数值模拟优化连铸结晶器

Use of FEM Simulation to Optimize Continuous Casting Moulds

结晶器用ZrCrCu合金氧化产物及强化机理分析

Analyses of Oxide and Strengthen Mechanism of Zr - Cr - Cu Alloy Used for Mould

基于RBF神经网络的结晶器激振在线监测与故障诊断软件模块

Software Module of Mold Oscillation online Monitoring and Fault Diagnosis Based on RBF Neural Network

珠钢CSP铸机液压振动结晶器的控制技术

Control technologies for hydraulic mould oscillation in Zhujiang steel plant CSP caster

另外，为得到熔化规律的关键知识，用原位高温X射线衍射方法对结晶器保护渣的熔化过程进行了研究。

Additionally , the melting of mould powders has been studied in-situ using high-temperature X-ray diffraction , to gain crucial knowledge about melting relations .

薄板坯连铸CSP结晶器液位波动影响因素的水力学模拟研究

Study of Process Parameters on Level Fluctuation in CSP Mould of Continuous Thin Slab Casting

PX氧化反应器-结晶器串联过程的数学模型

Models of Reactor-Crystallizer Connected in Series in p-Xylene Oxidation Process

连铸机结晶器铜板电镀镍-钴（Ni-Co）合金工艺

Technology of Electroplate Ni-Co Alloy for Sheet Copper of Continuous Caster Crystallizer

结晶器铜板本体材质改为Cu-Cr-Zr；

Use of Cu-Cr-Zr alloy as the mould copper plate ;

感应线圈与结晶器间的距离增大，磁感应强度明显减小，5～10mm的间距对电磁连铸过程较为有利。

The distance of 5 ~ 10 mm was favorable to electromagnetic continuous process .

用AUTOCAD作图检查弧形连铸机四连杆机构结晶器振动台的轨迹精度

By using AutoCAD draw method to check the locus accuracy of the crystallizer vibro-bench that fixed in the four articulated connecting rod assembly of the arc continues casting machine

连铸工字形异型坯结晶器铜板工作面电镀NiCo合金工艺

NiCo coating technology on copper plate working surface of mould for ⅰ - shape beam blank

120mm×120mm结晶器振动参数的优化

Optimization of Vibrating Parameter for 120mm × 120mm Mould

研究了包钢重轨钢从转炉出钢到结晶器各个工序过程（未经VD真空处理）钢液中氢含量变化。

The hydrogen content in the molten heavy rail steel was measured in every stages from LD tapping to mould ( without the VD refining process ) .

本文介绍了LB－352液位计在连铸结晶器钢水液位测量与自动控制中的应用。

This article presents the application of LB - 352 level detector in measuring and automatic controlling steel level in mold in continuous casting machine .

基于Fluent对水平连铸结晶器温度场分布及传热的研究笔者采用专门设计的热流传感器对弧形连铸圆坯结晶器的热流进行在线检测。

Study of Heat Transfer and Temperature Distribution of Mold Horizontal Continuous Casting Based On Fluent The heat flux of curved mold for round casting was measured by special designed heat flux sensor .

随着珠钢两机两流生产格局的形成以及电炉改造后生产能力的提高，提高连铸产能成了珠钢的一个瓶颈。CSP连铸结晶器的技术特点

With both lines running in Zhujiang steel , CSP continuous casting is being the bottleneck of the production after EAF updating . Technical Characteristics of the CSP Crystallizer for Continuous Casting

研究分析圆坯结晶器电磁搅拌（M-EMS）对圆坯质量的影响。

The effect of mould electromagnetic stirring on the quality of a round bloom is studied in this paper .

科学定位突出特色铸造以工科为主综合性一流民办高校CSP薄板坯连铸结晶器内钢水流动周期性失稳的机理与防止对策

Scientifically Locating , Laying Stress on Feature and Setting up a First-class Comprehensive Civilian-run Institute Put Engineering First ; Periodic Loss of Stability of the Fluid in CSP Thin Slab Continuous Casting Mold

同时表明，合适的结晶器厚度为10mm，合适的冷却水流速为9～12m/s。

The result also shows that the optimum mould wall thickness is 10 mm and cooling water rate is 9 ~ 12 m / s.

本文采用不可压缩MHD方程及零方程湍流模式，数值计算了加电磁制动器的二维薄板坯连铸结晶器中的流场。

Using incompressible MHD equations and zero equation turbulent model , the paper calculated the flow field in two dimension thin slab continuous casting mould with the electromagnetic brake ( EMBR ) .

介绍了宣钢炼钢厂通过对LF钢包精炼炉，连铸机中间包流场、结晶器、二冷配水等重要工序进行技术改造和工艺优化，提高了铸坯质量，为开发生产品种钢提供了保证。

Through the technical innovation and optimization of ladle refining furnace , continuous caster tundish , mould and secondary cooling zone , the steelmaking plant of Xuanhua Steel has improved its quality of continuous casting blank .

针对结晶器液压振动装置的特点，利用神经元的自学习功能构成自适应PID控制器，应用该控制器对结晶器振动装置的液压伺服系统进行控制研究，并给出了设计方法。

In view of the characteristics of hydraulic oscillating mechanism of mould , a self-adaptive PID controller is introduced based on the self-learning function of neuron . The controller is used in the hydraulic servo system of mould oscillating mechanism and its design method is put forward .

通过对钢液结壳和粘结报警的分析，对XCN-Z型结晶器保护渣成分进行了调整和优化。

According to analyzing of the two problems , the composition of the mold flux was adjusted .

基于建立的PCA模型对大量的异常数据进行仿真，利用T~2图和Q图进行故障检测，结合实测的结晶器摩擦力及其均方根图进行分析。

Appling PCA model to analyze a large number of abnormal data and the fault detection is performed by means of the T ~ 2 and Q charts , the MDF and its root-mean-square charts are used to analyze the condition of process .

EMBr对板坯结晶器钢液流动、传热及夹杂物去除的影响不锈钢/普碳钢复合连铸结晶器内流场实验研究

Effect of EMBr on fluid flow , heat transfer and inclusion removing during CC Experimental Investigation on Flow Field in Continuous Casting Mold for Clad Steel