局部加热

  • 网络local heating;localized heating
局部加热局部加热
  1. 运用ANSYS软件对圆柱体坯料局部加热和局部冷却过程进行了热分析。

    The process of local heating and local cooling on cylinder billet is analyzed by the ANSYS software .

  2. 本文采用FLUENT软件,建立五种不同局部加热面积的墙体传热模型,且通过实验验证墙体传热模型的准确性。

    In this paper use the FLUENT software to Set up five different local heating area of the wall heat transfer model which need the accuracy verification by the experiment .

  3. LED感应局部加热封装试验研究

    Research on Localized Induction Heating for LED Packaging

  4. 使用扫描隧道显微镜(STM)产生的隧道电流作为热源对磁膜进行局部加热。

    Scanning tunneling microscopy ( STM ) current was introduced to heat the medium locally .

  5. 对感应局部加热实现MEMS封装键合进行了初步研究。试验中选用功率为1kW、频率为400kHz的高频电源,通过对感应线圈优化设计,实现了硅片上的焊料图形键合。

    By choosing suitable frequency of high frequency power supply and optimizing the induction coil , local induction heating for MEMS bonding has been investigated .

  6. 论述了RTM模具热平衡设计的重要性、热平衡设计的内容和方法,以及模具材料的热传递性能、模具的热平衡分析、加热系统和局部加热系统的设计。

    The importance , the content and method of thermal balance design for RTM mould are discussed as well as the thermal transmission of the mould materials , the heat balance analysis the healing system and the local heating of the mould .

  7. 加热治癌方法有全身性加热、区域性加热和局部加热法。

    The heating method includes general , regional and local heating .

  8. 中频感应局部加热弯管回弹的研究

    Investigation into Springback of Pipe Bending Using Local Induction Heating

  9. 用局部加热法测量不良导热材料的导热系数

    Measuring Thermal Conductivity of Poor Conductors by Local Heating Method

  10. 局部加热对重质油加氢裂化的影响

    Effect of Local Heating on Hydrocracking of Heavy Oils

  11. 测量隔热材料导热系数的一个新方法&局部加热法

    A New Method for Measuring Thermal Conductivity of Insulators & Local Heating Method

  12. 应用于微系统封装的激光局部加热键合技术

    Laser locally heating and bonding for microsystem packaging

  13. 锗-硼硅玻璃局部加热低温封接温度场研究(玻璃温度计的)感温泡

    On the Temperature Distribution in Localized Heating for Low Temperature Sealing of Germanium-Borosilicate Glass

  14. 在持续稳定的局部加热下,这一动态过程循环地发生,周期为几个小时。

    With a steady heating , this process repeats with a periodicity of several hours .

  15. 管件局部加热缩口、镦粗复合模设计与成形工艺

    Design and shape technology of shrinking and upsetting compound mould by partly heated tube workpiece

  16. 温度程序控制系统在局部加热粘接瓷套中的应用

    Application of Programed - control System of Temperature at Local Heating of Insulators for Cure-bonding

  17. 大直径厚壁管中频感应局部加热弯管工艺研究

    Investigation Into Pipe Bending Process of Large Diameter and Thick Wall Pipe by Using Induction Heating

  18. 扬恩·塞勒内·于雷热预热与局部加热系统

    Preheat and hot spot system

  19. 界面层是整个接头的薄弱部位,由于激光的局部加热特征,界面层的厚度分布极不均匀。

    Because of local heating of laser beam , the thickness of interfacial layer is very uneven .

  20. 结论:替加氟温度敏感性脂质体配合肝脏局部加热可提高其靶向性。

    Conclusion : Fluoroful temperature-sensitive liposomes can be controlled to release specifically into livers by heating the organs .

  21. 微波局部加热联合化疗治疗口腔颌面部恶性肿瘤的初步报告

    Preliminary Report of Microwave Localized Hyperthermia Combined with Chemotherapy on the Malignant Tumor of Oral and Maxillofacial Region

  22. 传统的产生热应力方法是通过火焰或激光局部加热来实现的。

    At present , the traditional approach to cause thermal stress is local heating by flame or laser .

  23. 以往采用火焰淬火和盐浴局部加热淬火,其效果不理想。

    The former flame quenching and quenching after local salt bath heating for it could not obtain good result .

  24. 介绍了温度程序控制系统在局部加热粘接瓷套中的应用,对控制系统的构成、工作原理作了详细的论述。

    The application of programed control system of temperature at local heating of insulator for cure bonding is introduced .

  25. 激光热成形利用高能激光束对工件局部加热诱发不均匀热应力,使板材产生塑性变形,以获得所需要的目标形状。

    Laser forming is a flexible forming technology which forms sheet metal by means of laser-induced non-uniform thermal stress .

  26. 微波焊接具有接头强度高、升温速度快、局部加热、易于控制温度等优点。

    Microwave joining has advantages such as high joining strength , rapid , local heating and precise temperature control .

  27. 提出了利用激光进行局部加热真空封蜡的封装方法。

    The method of local heating by laser has been used during the process of vacuum sealing wax encapsulation .

  28. 局部加热条件下长气泡上下游端分别出现蒸发和冷凝。

    At local heating condition , evaporation and condensation occurred at the upstream and downstream caps of an elongated bubble .

  29. 结果表明,采用局部加热冷却的方法可以有效地减小叶片危险区域的残余拉应力峰值。

    The result shows that the method of local heating-cooling can decrease the residual tensile stress peak in dangerous area of the blade .

  30. 激光由于具有高能量输入密度以及可局部加热的优点而在面阵列电子封装钎料凸点成形中具有潜在的优势。

    Laser reflow bumping becomes a potential technique due to the unique characteristic of laser such as high energy input density and local heating .