载板

采用高性能的磁盘阵列和I/O控制载板，同时结合定制化设计的零延时换序PMC卡，使得单通道数据回放速率可以达到512Mb/s，满足了系统的设计指标。

With using the high performance disk-group and I / O controller carrier , and the zero delay format converting PMC card , the playback data rate of single channel can reach 512Mb / s and meet the require of the system design .

但由于时间与条件的限制，载板管理软件的功能还有待进一步完善。

Because of the limit to time and condition , the functon of AMC Carrier management software is not perfect .

通过一块CPLD读取和识别载板信息，做到自动适应不同的载板。

A CPLD is used to read and recognize information , so that automatically adapt to different carrier boards .

将水泥土桩、土体、桩顶压载板及桩土接触面简化成有限元集合体；

Cemented soil pile , soil , bearing plate on pile top and pile-soil contact surface are simplified as FEM system .

星载电路板引脚断裂问题的分析和解决

Pin breakage analysis and solution for satellite ′ s circuit panel

载流板中半无限裂纹形成瞬间尖端域的应力场

Instant stress field around semi-infinite crack tip in a conducting plate

双向受载裂纹板的胶接修补效果分析

Study on bonded repair efficiency of cracked plates under biaxial loading

双向受载裂纹板的复合材料补片胶接修补

Study of cracked plate repair with composite patches under biaxial loading

无限长载流导体板磁场分布的计算

Calculation of Magnetic Field Distribution of an Infinite Current-carrying Ribbon

钉载作用下层板多孔过盈配合分析

Analysis of Composite Laminate with Multiple Interference Fitting Load-Pins

最后，根据弹脆性材料的损伤本构关系确定受载复合材料板的真实应力场。

Finally , the real stress fields of the composite plate loaded can be determined from the constitutive relation of damaged elastic material .

为此，针对拉深成形，分别采用平板滑动摩擦实验和拉弯摩擦实验，研究了变速/变载条件下板料在法兰处和凹模圆角处的摩擦行为。

The friction behaviors in the flanges area and die corner radius area during the variable forming speed / forming loading stamping process are studied by flat plate friction test and stretch bending friction test .

本文根据广义弹脆性损伤理论模型，用综合实验分析和数值计算的方法，确定受载复合材料板的形变场和损伤场。

Based on the generalized elastic - brittle damage theoretical model , an experimental-numerical Synthetical method for determining both the deformation-and the damage-field of the composite plate in the loading process has been presented in this paper .

应用虚拟功的互等定理求解均载悬臂厚矩形板的弯曲

The Calculation of Thick Cantilever Rectangular Plate By Virtual Reciprocal Theorem

转台是铁路起重机的关键结构件之一，它是一种三维受载的大型空间板梁结构，受载状况和结构型式均较复杂。

Rotating platform is a key structural component on railroad crane . It is large special plate and beam structure loaded in three dimensions with relatively complex load condition and structure pattern .

本文分析了导弹飞行的弹体振动环境，计算了弹载计算机印刷线路板的自振频率，并给出了一个抗振可靠度的计算公式。

This paper analyses flying missile 's vibration environment . Computation of the self-vibration frequency of the printed circuit board of on-board computer and a computational formula for anti-vibration reliability are presented .

热段可选配压力辊压载系统、短棍压载系统、热压板压载；

Pressing roll , cosh pressing roll or EUTAC system are used in heating section .

并就其形式对截面抗弯能力的影响谈了自己的看法，认为截面抗弯载力可采用简化塑性法进行计算，截面抗弯载能力随板托面积增大而增大。

The bend strength of section can be calculated by using simplified plastic methods and the resistance ability of bend of a section can be changed with the area of the plate bracket .