轴角

轴角型模/数转换器及其在煤矿中的应用

Axial Angle Mould / Number Converter and Its Application in the Mines

光电轴角编码器是一种应用广泛的光电角位置传感器。

The optical electric axial angle encoder is a kind of widely used optical electric sensor for angle detecting .

基于光电轴角编码器和PLC控制的新型气-液联合缸机械手

New air-liquid unit cylinder manipulator based on photoelectric shaft encoders and PLC controlled

基于FPGA的嵌入式通用轴角测角平台系统的研究

A Survey on Embedded System of Measuring Axle - Angle Based on FPGA

基于DSP的高精度旋转变压器轴角数字转换器

High-accuracy resolver-to-digital converter based on DSP

基于PCI总线的单圈绝对式光电轴角编码器实时数据采集系统

Real-Time Data Acquisition System of Single-Ring Absolute Optical Shaft Encoder Based on Pci Bus

CPLD在雷达伺服轴角编码电路中的应用

The Application of CPLD in Radar Servo Encoder Circuit

该伺服系统采用交流驱动方案、轴角检测系统和智能PID控制方案实现了系统的全闭环控制。

The closed-loop control is realized by applying AC driving scheme , Resolver-to-Digital converter system and intelligent PID control strategy .

轴角编码STD模板的设计与实现

The Design and the Implementation of Angle Coding in STD Modular Board

基于ISA总线的轴角数字转换卡设计

Design of Based-on ISA Bus SD Converting Card

本文以汽车AMT系统的离合器接合过程为控制对象，引入Δ变换离散描述，设计极点配置控制器，跟踪理想输出轴角速度。

A pole placement controller to track the ideal angle velocity of output shaft .

本文所研制的DSP轴角检测板经试验验证基本达到了在数控加工技术中的应用要求，具有良好的实用价值和应用前景。

The DSP axis-angle detecting board has been proved successfully and has satisfied the requirement of numerical control machining and holds application values and excellent foreground .

详细介绍了CPLD的内部功能电路、CPLD轴角粗精组合和纠错实现电路，以及CPLD的工作时序图。

The circuits of function , the combined circuits and the working clock drawing in CPLD are discussed in detail .

介绍了一种针对单圈绝对式光电轴角编码器而设计的基于PCI总线的实时数据采集系统。

A real-time data acquisition system based on PCI Bus was introduced . The system was designed for single-ring absolute optical shaft encoder .

一种采用EPROM的数字-轴角转换方法

A Method of Digital to Shaft angle Conversion Using EPROM

在软硬件设计中，完成了硬件电路设计，控制板集成浮点DSP芯片、通信模块、DA转换模块、轴角转换模块和故障显示模块等，实现了控制平台的搭建。

Control board integrates DSP , communication module , DA module , angle conversion module and fault display module while installed in the control cabinet , realizes to build the control platform .

单片轴角数字转换器（RDC）及其精度校验

The Monolithic Resolver-to-digital Converter and Its Accuracy Verification

在完全相同的实验条件下对DSP轴角检测板和专用模块、单片机轴角检测板的检测性能进行了对比，试验结果表明：DSP轴角检测板基本可以代替专用模块。

Under the same experimental conditions , the performance of the DSP board is compared to the special module and single-chip 's. The results show that the axis-angle detecting board of DSP can substitute the specific module .

本文介绍了球面孔系坐标非接触测量系统组成结构、原理和工作过程，以及系统使用到的CCD、光栅传感器和轴角编码器等光电技术。

This paper firstly introduces the elements and working principle and process of the measurement system , together with some photoelectric technology used by this system such as CCD , raster sensor , and photoelectric rotary encoder .

接下来主要研究了基于垂直陀螺和GPS，以及基于三轴角速率陀螺和GPS两种传感器配置情形的最简控制技术，并将线性二次型LQ技术运用到最简控制的控制律设计中。

Two kinds of cases are studied : the vertical gyroscope and GPS are equipped ; the angle velocity gyroscope and GPS are equipped . The minimum-sensors control system is studied separately for the cases .

ZSZ01利用模拟速度电压输出端VEL来进行轴角转动的方向判别。

ZSZ-01 system can perform direction judgment of axial angle turning by means of output signal VEL of anolog speed voltage .

面角、颌突角、ANB角、Y轴角、面轴角和上唇突度与髁突垂直向位移呈显著相关。

NP FH , NA PA , SNB , ANB , Y axis , FA and UL EP correlate significantly with the vertical condylar displacement .

用简化应力的分析方法推导了SiCwAl复合材料的强度与SiC晶须偏轴角α的关系，并通过试验进行验证.偏轴拉伸测定复合材料剪切特性的研究

The relationship of the strength of the SiCw / Al composite and off-axis angle of the SiC whisker is studied with the analysis method of the simplified stress . Investigation on Off-axis Tensile Test for Determination of Shear Characterization of Composites

该设计采用专用轴角转换模块、高性能单片机和USB接口芯片为硬件平台，通过采集分析软件的开发，实现了多通道组合轴角数据采集、显示和存储功能。

In the design a professional axial angel conversion module , high performance single chip and a USB interface chip are used to form the hardware . The functions of combined multi-channel axial angel data acquisition , display and data storage are implemented by developing the sampling and analytical software .

本文介绍高精度绝对式19-bit、21-bit光电轴角编码器的工作原理、具体结构、精度和可靠性等。

The principle , mechanism , accuracy and reliability of 19-bit and 21-bit absolute photoelectric shaft angle encoder - with high accuracy are described .

结果双尖牙减数治疗后MP-SN、PP-SN、MP-PP、Y轴角和S-Go/N-Me无显著性变化；

Results After treatment , the change of MP-SN , PP-SN , MP-PP , Y-axis and S-Go / N-Me was not significant in both groups .

结果患者上下颌骨关系明显改善，前牙牙槽高度、后牙牙槽高度、ANB角、上下中切牙轴角及16岁以下患者下颌体长度矫治前后有显著性差异。

Results The height of anterior and posterior alveolar , ANB angle , anterior axis of central incisors , and the Go - Gn linear measurement for the patients under 16 years old showed significant differences before and after treatment .

运用双速轴角转换原理中的数据组合与数据纠错原理，基于轴角转换芯片RD-19230，研究一种新型的双速处理器。

Exerting data combination and data correct theory of two-speed shaft angle converter , it researches a new type two-speed processor based on shaft angle conversion monolithic of RD-19230 .

本文分析了轴角编码器中粗精组合与纠错的基本原理，并基于160DD×4／16多线旋转变压器，提出了运用纯硬件电路实现编码纠错的一种简单方法。

This paper analyses the basic philosophy of coarseness-precision combining and its error correcting in a shaft position encoder . On the basis of a 160DD × 4 / 16 multiwire rotatory transformer , a simple method of correcting encoding errors is given by using pure hardware circuits .

机械回转体轴角位移精密测量研究

Research on fine axis angle - displacement measurement of mechanical rotator