设计误差

波形存储LFM信号源设计误差分析

Analysis of Errors in Waveform Storage LFM Generator Design

瓦特森-瓦特测向工程设计误差源分析

Analyze on Error Source of Watson-Watt Direction Finding Method in Engineering

基于有限点振速分布设计误差传感策略

A strategy for designing error sensor based on limited vibration velocity distributions

粉末冶金齿轮成型模具的设计误差

Design Error on Forming Mold of Powder Metallurgy Gear

半导体式甲烷气体探测器设计误差分析及解决方法

The Design and Error Analysis of Combustible Gas Detectors Based on Semiconductor Technique

热管换热器换热量设计误差估算

The design error estimation of the heat transfer rate in the heat pipe exchanger

空间凸轮机构设计误差分析与单侧面加工理论及实验研究

Design Theory , Error Analysis and One-side Process Principle of Spatial Cam Mechanism and Experiment Research

本文在推导出齿形误差计算公式的基础上，给出一种使齿形设计误差最小的最佳齿形角的求法。

The tooth profile error and longitudinal form error are calculated , and the change rule with setting angle of them is got .

此外，在以前分析计算吸波材料的反射率与入射角的关系时，常采用性线插值法，这会引入较大的设计误差。

Besides , In analysis of reflectivity versus incident angle of absorbing materials , it used to use linear interpolating method and resulted in considerable error .

以武器必须命中目标为约束条件，建立了构思模型、控制模型与瞄准误差、设计误差的关系方程。

With the constraint conditions that weapons must hit targets , the relation expressions between conception model and control model vs. pointing error and design error have been established .

从总体上看，设计误差放大器包括两个主要步骤：第一步是架构的选择，第二部是设计参数的优化。

Overall , the design of error amplifier consists of two main steps : The first step is the choice of architecture , and the second is the optimization of design parameters .

在大偏心、小流性指数与小流量时，用该计算方法进行精确计算，可避免因工程设计误差而导致的工程事故。

Conclusion then was drawn out when to calculate fluids of high eccentricity , low liquidity index , and low flow rate , the studied method should be taken to prevent designing error .

然而国内长期采用日本通用翅片性能曲线，使得国产板翅式换热器的热力设计误差很大。

However , being lack of our own fin surfaces performance curves , the thermal design error of the plate-fin heat exchanger made in China is quite large by using the general curves from Japan .

本研究在严密证明角规测树原理的基础上，分析了杆式角规的设计误差，并提出修正方法，使角规原理与工具设计相统一，进一步完善了角规测树体系。

On the basis of the precisely proving about the principle of angle gauge , the errors about the design of pole type angle gauge were analyzed , and the revised method on the errors was provided .

本文在原有基础上，增加了数学推导，由实测边界数据计算出投射中心的准确位置，并对设计误差进行了测算，从而使该方法更加完善。

In this paper , based upon it , making mathematical derivation , calculation of the accurate position of projection center from the actual boundary data taking measurement and calculation for the design error make the method being perfected .

文章对我国某些情报政策效应偏差进行了实证分析，认为出现这些效应偏差的人为原因是情报政策设计误差、情报政策执行走样和情报政策对象抗阻。

Focused on the situation analysis on the policy deviation in the country , the article deduces that the artificial reasons of the deviations are the designation fault , the misconduct , and the target resistance to the information policy .

基于FPGA的DDS信号源设计及误差分析

Design and Error Analysis of DDS Signal Generator Based on FPGA

CAPP设计中误差模型的建立

Building of Error Model in the CAPP Design

采用Delphi数据库软件技术，设计加工误差实验数据采集、分析软件。

Delphi database software was adopted to design the data collecting , analyzing and drawing software of machining error in the experiment .

最后对GPS在该系统中应用的选星、滤波器设计、误差消除等问题进行了讨论。

Finally , some related problems , including GPS satellite selection , filter design , error elimination , etc. about the applications of GPS in the system are discussed .

采用信号四阶和六阶统计量提取信号特征，使用新设计的误差函数训练RBF神经网络，使得识别的效率和正确度得到了明显的改善。

The forth-order and sixth-order cumulants of received signal are adopted for features extraction while RBF neural networks with a new designed training cost function being used for classifier .

使用Backstepping算法，设计了误差系统鲁棒自适应逆最优控制器和参数自适应律，从而解决了原系统的鲁棒自适应逆最优跟踪问题，并给出性能估计。

The inverse optimal controller and parameter adaptive laws were designed by using Backstepping algorithm , thus solving the robust adaptive inverse optimal tracking problem was solved for the continuous system .

本文主要利用轨迹补偿法加工非球面光学零件的原理，进行加工口径为φ200～φ300mm的非球面光学零件的机床设计及其误差分析。

This article mainly use the principle of the path compensation method to processing aspheric surface optics components , aspheric surfaces optics components engine bed design of carrying on the processing diameter of 200 ~ 300 millimeters and its the error analysis .

最小误差空域预滤波器设计及误差分析

The design on spatial pre-filtering of minimum variance and error analysis

微惯性测量单元设计及其误差补偿模型的研究

Design of a MIMU and Study on Model of Error Compensation

毫米波引信天线的仿真设计与误差分析

The Simulation Design and Error Analysis of Millimeter Wave Fuze Antenna

石油钢管长度测量系统优化设计及误差分析

Optimization and Error Analysis for Petroleum Steel Pipe Length Measuring System

内表面间垂直度的高精度测量方法设计与误差分析

A High Precision Perpendicularity Measurement Method and Analysis for Internal Surfaces

月球软着陆制导律设计及其误差分析

Guidance Law Designing and Its Errors Analyzing for Lunar Soft Landing

惯性测量组合的优化设计与误差补偿算法研究

Optimization design and research on error compensation algorithm of inertial measurement unit