碳化硼
- 网络Boron Carbide;CBN
-
以酚醛树脂(phenol-formaldehyderesin,PF)和碳化硼(B4C)为原料的高温粘结剂对炭材料具有良好的粘接性能。
The high temperature adhesive composed of phenol-formaldehyde resin ( PF ) and boron carbide ( B 4C ) has satisfied bonding performances for carbon materials .
-
掺碳碳化硼活化烧结及其动力学
Activated sintering and sintering kinetics of boron carbide with carbon as activator
-
制备高B(6.5)C相含量碳化硼粉末的工艺探讨
Study on the preparation of rich B_ ( 6.5 ) C boron carbide powder
-
碳化硼固相烧结微观结构演化的同步辐射CT观测
Microstructures-evolution Observation of Boron Carbide Ceramic during Sintering Process by Synchrotron Radiation X-Ray Computed Tomography
-
碳化硼颗粒增强Cu基复合材料的研究
Studies of B_4C Particles Reinforced Copper Matrix Composite
-
高B4C相含量极细碳化硼粉的制取
A study of superfine boron carbide powder with high b_4c phase content
-
所制备的碳化硼涂层中除了含有碳化硼外,还含有B和C的一些其他相。
Except for boron carbide , other phases such as B_ ( 13 ) C_2 , FeB , C are also found in the coating .
-
碳化硼涂层中还发现了由B、O和Fe三种元素组成的杂质相,其显微硬度比碳化硼低,这是碳化硼涂层显微硬度同碳化硼陶瓷相比要低的一个重要原因。
Another impurity phase , which consists of B , C and Fe elements , will decrease the microhardness of B_4C coating .
-
SPS制备致密碳化硼陶瓷的结构及性能
Structure and Mechanical Properties of Densified Boron Carbide Ceramics by SPS
-
本文阐述了立式冶炼炉(以下简称A)和卧式冶炼炉(以下简称B)两种冶炼方式冶炼的碳化硼粉末的不同性能,以及利用粉末热压烧结制成的碳化硼陶瓷间性能对比;
This paper describes the different properties of boron carbide powders produced respectively in vertical smelting furnace ( called powder A for short ) horizontal smelting furnace ( called powder B for short ) .
-
应用离散变分Xα量子化学分子轨道计算方法,根据5类共28个不同的结构模型,研究了碳化硼及掺硅系列组成,结构,化学键及热电性能之间的关系。
The correlation among composition , structure , chemical bond and thermoelectric property of boron carbide and Si doped ones was studied using DV X α method , with 5 classes of 28 models .
-
本文采用热压方法,利用碳化硼和碳化钨之间的固相化学反应,原位生成C/W2B5复合材料。
In the present work , the composite of C / W_2B_5 was fabricated by an in-situ reaction between B_4C and WC .
-
本文以碳化硼颗粒增强铝基复合材料板材(B4Cp/Al)和纯钛(Ti)板材为原料,研究了多层Ti–B4Cp/Al板的叠轧及热处理。
In this paper , boron carbide particle reinforced aluminum matrix composite ( B4Cp / Al ) sheet and pure-titanium plate are used for raw materials , and the process of multi-layer combined rolling deformation and heat treatment is studied .
-
结果表明:炭黑和硼粉加入量(w)分别为45%和55%时,经自蔓延燃烧反应后可以得到粒度均匀的碳化硼(B4C)粉体,且碳黑已部分石墨化。
The results show that : B_4C powder with uniform size distribution is prepared with 45 % carbon black + 55 % boron powder , and the carbon black is partly graphitized .
-
用碳热还原法制取高化学剂量的B4C细粉,细粉经气流粉碎制得微米级B4C粉末。经致密化工艺得到碳化硼屏蔽吸收芯块。
The boron carbide pellets were manufactured using fine powder which is fabricated by carbon reducing boron oxide and then by air flow attrition .
-
介绍了用GAP、TDI、AP、TMP、LiF、VitonA、硅烷、碳化硼、钛等物质包覆硼粒子的工艺过程,论述了其包覆机理对硼粒子表面及点火燃烧特性的影响。
The process of coating boron particles with GAP , AP , LiF , Viton A , B 4C etc is introduced . The coating mechanism and effect on the surface characteristics and combustion property of B particles are discussed .
-
离子束增强沉积制备碳化硼及C-B-Ti化合物薄膜的结构与力学性能的研究
The structure and mechanical performance of boron carbide and c-b-ti compound films by IBED
-
在载荷为1~6μN下,研究了Si3N4探针扫描碳化硼表面时摩擦力的分布。
The samples used are of good consolidation and the surfaces of the polished samples are even . The friction force distributions of Si_3N_4 tip scanning over the boron carbide surfaces were investigated at load 1 μ N to 6 μ N , 1 μ N a step .
-
当硼化镧添加量为6%的时候,断裂韧性达到最大值5.14.MPa·m1/2,比单一碳化硼提高了39.67%。
When the amount of the lanthanum boride is 6 % , the fracture toughness reaches its supreme value of 5.14 MPa · m1 / 2 , which is improved nearly 39.67 % compared to single phase boron carbide materials .
-
采用真空等离子喷涂技术,在不锈钢基体上制备碳化硼(B4C)涂层,并对涂层的组成、结构、沉积效率、结合强度以及抗激光辐照性能进行了表征。
Boron carbide coatings were deposited onto stainless steel via vacuum plasma spraying ( VPS ), and then their phase composition , microstructure , deposition efficiency , bonding strength and laser irradiation resistance were examined .
-
经过广泛调研和充分的论证,本研究选取ZL205A合金作为基体,碳化硼颗粒作为增强体,采用搅拌复合的方法在空气状态下制备出用于实验的复合材料。
Following the choice of the materials , taking ZL205A alloy as the matrix and boron carbide as the reinforcement , the experiment was carried out in air by the stir-furnace .
-
对于100~200A的氩等离子弧,无论是熔点较低的铁基粉末颗粒还是熔点较高的碳化硼颗粒,被加热到熔化温度所需要的时间都在毫秒级水平(几毫秒至几十毫秒)。
In the central plasma fluid with 100 ~ 200 A surfacing currents , not only the Fe base particles with a relatively lower melting point but also the boron carbide ( B 4C ) particles with a relatively much higher melting point might be fully fused within milliseconds .
-
碳化硼涂层显微结构和性能研究
Relationship Between Properties and Microstructure of Plasma Sprayed Boron Carbide Coating
-
硼酐碳热法合成碳化硼的研究
Study on the Boron Oxide Carbothermal Reduction Synthesis of Boron Carbide
-
碳化硼超细微粉团聚及解决方法
Research for Reunion and Resolve Method of Boron Carbide Submicron Powder
-
碳化硼对环氧胶粘涂层机械性能的影响
The Effect of Filler on Characteristic of the Epoxy Adhesive Coating
-
初步探索了在本文工艺条件下,碳化硼与铝的微观界面结构和界面反应。
The microstructure and the reaction of the interface are analyzed .
-
核级碳化硼试样分解方法的研究
Study on the decomposing method in samples of nuclear-grade boron carbide
-
碳化硼改性酚醛树脂的高温结构演变特性
Study on the microstructure evolution of phenol-formaldehyde resin modified by ceramic additive
-
碳化硼-碳化硼摩擦副的摩擦磨损特性研究
Friction and Wear Properties of Self-mated Hot-pressed Boron Carbide Pair