浇口

CAE技术在优化塑件浇口中的应用

Application of CAE Technology in the Optimization of the Gate of Plastics

基于MPI注塑产品浇口设置及流动分析

Gate Placement and Flow Analysis of Injection Part Based on MPI

多浇口热流道注射成型PET瓶坯

Multi-cavity injection molding with hot runner to produce PET bottle

扇形浇口热流道注射成型PP方椅背靠

Injection of PP armchair back through fan gate and hot runner

ABS圆盒盖单浇口热流道注射成型

Single-gate injection molding for ABS caps with hot runner

基于CAE技术的收纳盒注塑模浇口优化设计

Optimum gate design of the storage-box injection mold based on CAE technique

热流道板的设计成功，为PET瓶坯多浇口注射成型奠定了基础。

The successful design of the hot runner plate lays a foundation of multi-cavity injection of the PET bottle .

基于CAE技术优化ABS弯头管件的浇口位置

Optimization of the placement of the gate of an ABS angle fitting based on CAE Technology

介绍ABS圆盒盖单浇口热流道注射成型模具，进行了注射成型试验。

This paper introduces the design of the single-gate injection mold for ABS caps with hot runner .

薄壁HDPE桶用热流道点浇口式模具

Pin - Point Gate Type Hot - runner Mould for Thin Wall HDPE Buckets

用MPI分析注射成型工艺确定浇口数量

MPI-based analysis of injection molding process and setting of sprue

基于MPI技术的塑料制件浇口位置的优化设计

Optimum Design of Gate Location of Plastics Product Based on MPI Technology

车用PBT长臂灯架防翘曲注射浇口设计分析

Anti-warpage Gate Design Analysis for Injection-molded PBT Long-armed Lamp Holders

基于MPI的磁疗仪注射模浇口优化设计

Optimization Design of Gate for Injection Mold of Magnetic Treat Instrument Based MPI Technology

基于MPI的塑件浇口优化设计

MPI-based optimization design of injection forming sprue

潜伏式浇口的缺陷及维修基于MPI的塑件浇口优化设计

The Defects of the Submarine Gate and Its Maintenance MPI-based optimization design of injection forming sprue

并以聚丙烯（PP）为原料，对比分析了PP熔体流经常用点浇口和孪浇口时的剪切速率、压力降、温度和粘度的变化。

Changes in shear rate , pressure drop , temperature and viscosity of PP melt passing through the twin-gate and the pin gate were studied .

利用浇口可以更换的阿基米德螺旋线模具，研究了HDPE塑料的螺旋线流动长度（简称螺旋线长度）和浇口直径的关系。

Using Achimedean spiral mold with changable gate , the relationship between gate diameter and spiral lengths of HDPE was studied .

比较结果表明“C”站址（中站址）为最优。预测可能存在的气泡位置及锁模力的大小，确定最佳浇口位置。

The station " C "( the middle station location ) is the best . In order to obtain the best gate location addition , the position of air bubble and the clamp force were forecasted .

研究了多浇口一模四腔热流道注射成型PET饮料瓶坯的模具结构、成型工艺，取得良好效果。

This paper deals with the mould structure and molding process of the multi-cavity injection mould with hot runner to inject PET bottles , which leads to higher productivity .

当PP熔体温度为240℃时，熔体流经孪浇口和点浇口后，温度的增加值分别为251℃和113℃。

When PP melt temperature is at 240 ℃, temperature increments of the melt through the twin-gate and the pin gate are 25.1 ℃ and 11.3 ℃, respectively .

采用CAE模拟辅助进行微流道微换热器模具的设计，对模具的浇口，流道以及冷却水道的开设进行的优化。

Using CAE to design the mold of micro heat exchanger and optimizing the mold gate , flow runners and the cooling water channels .

随后分析了成型物料和浇口的技术参数，构建了QFD成型物料选择和浇口设计的过程模型。

Second , the paper analyzed the technical parameter of selection , set up a quality function deployment process model .

利用C－MOLD软件对其进行充模分析，确定出最佳的浇口位置、数目及尺寸，并为用户提供最佳的工艺方案。

The mould filling was analyzed to determine the most good location , the numbers and dimensions of gates by use of C-mold software . So that the most good technology parameters could be provided to users .

本文是关于保护罩注塑模具的设计，在正确分析塑件工艺特点和PP的性能的基础上，采用了环形浇口。

This article is about the protective cover design of injection mold , plastic parts in the correct analysis of process characteristics and performance of PP on the basis of a ring gate .

进而应用CAE软件进行分析，通过调整浇口位置，对熔接痕的长度进行优化，使其减少到最小，结果得到实践验证。

Then using CAE analysis and through adjusting the gate position , weld lines can be optimized to the minimum length , and this result has also been identified by practice .

应用MPI软件对税控收银机外壳制品的浇口位置进行优化设计。

Moldflow Plastics Insight ( MPI ) was applied to optimize the design of gate location of an injection mould for the face cover of a cash register .

在所关心的模具型腔尺寸范围内，径向温度梯度大于3.5℃／mm，且中心浇口温度高于边缘温度，这种温度梯度分布特征有利于硅片凝固应力的及时释放，避免硅片的破裂；

Within the interesting domain of the mold cavity . the radial temperature gradient is oyer 3.5 ℃ / mm . which is helpful to the relaxation of the solidification tension for avoiding the breakdown of the silicon sheet .

针对薄壁听筒上盖零件的成型工艺及产品性能，应用Moldflow的MPI模块进行分析，确定了浇口位置及数量。

The moulding processes of phone are analyzed by using moldflow / MPI to conform the number and location of gate .

介绍了PP方椅背靠的形状，研究了扇形浇口热流道注射成型PP方椅背靠的模具结构及运行特征，分析了扇形浇口的设计。

The shape of PP armchair back was introduced . The mould structure and process characteristics for the injection of PP armchair back through fan gate and hot runner were studied . The design of fan gate was analyzed .