浇铸法

以淀粉、聚乙烯醇为基本原料，甲醛为交联剂，甘油为增塑剂，用浇铸法经PVC疏水化处理后制备了聚乙烯醇&淀粉生物降解膜材料。

With starch and polyvinyl alcohol as basic materials , formaldehyde as crosslinking agent , glycerol as plasticizer , polyvinylalcohol-starch biodegradable agriplast film materials were prepared by casting process , through PVC hydrophobic processing .

用溶液浇铸法（solventcastingmethod）制得了聚甲基丙烯酸凝胶电解质膜，室温的最高电导率为2.3×10-4S·cm-1。

Poly ( methyl acrylic acid ) gel electrolyte membrane containing water was produced using solvent casting method . The highest conductivity at room temperature was 2 . 3 × 10-4S ?

介绍旋转浇铸法制作，MC尼龙管浇铸量计算公式。

This paper reports an equation used several years since 1993 for weight calculation of casting MC Nylon tubes .

利用预混法对苯乙烯-乙烯/丁二烯-苯乙烯三嵌段共聚物（SEBS）进行了磺化，采用溶液-浇铸法成膜，并对其制备过程和膜的性能进行了研究。

A hydrocarbon proton exchange membrane , the sulfonated styrene-butylene / ethylene-styrene ( s-SEBS ) three blocks copolymer membrane , was prepared by the method of solution casting . The process of synthesis and the performance of membranes were studied .

目前，凝胶聚合物电解质膜常用的制备方法是Bellcore技术和溶液浇铸法，得到的膜具有物理交联型结构。

At present , the common preparation methods for PGE are Bellcore and solution-casting technology , and it is physically cross-linked for the PGE produced by Bellcore and solution-casting technology .

采用钢的连续浇铸法很重要。

Of great importance is the introduction of continuous steel pouring .

汉代平板陶范竖式浇铸法铸钱工艺的研究

The clay-mold bunch-casting technique for casting of Han Dynasty coins

浇铸法测试钢丝绳整绳破断拉力试验方法

Introduction of the Cast Method to Examine Aggregate Breaking Force

奥诺连续浇铸法生产挠性铋丝

Flexible Bismuth wires Produced by the Ohno Continuous Casting Process

分层浇铸法研制松香改性不饱和聚酯人造大理石板材

The Development of Artificial Marble Sheet from Rosin Acid Unsaturated Polyester by Layered Casting

多晶硅锭的制备工艺主要包括定向凝固法及浇铸法。

The production process for making poly silicon mainly includes directional solidification and casting methods .

旋转浇铸法小芯径掺杂氟化物玻璃光纤预制棒的研制

The Technique of Preparing the Preform of Small Core Doped Fluoride Glass Optical Fiber by Rotational Casting

采用溶液浇铸法分别对3种改性蒙脱石与聚氧乙烯、LiClO4进行复合制备了聚合物电解质膜。

Composite polymer electrolytes were prepared with solvent casting technique to form complex modified montmorillonites with LiClO_4 and PEO ( polyethylene oxide ) .

采用精密浇铸法制作了环氧树脂扁挤压整体筒和组合筒模型，使得内腔一次成型。

The precise-casting method is used to make both the integral and the composite epoxy resin models , through which the cavities are formed at one time .

用溶液浇铸法在壳聚糖中引入的不同分子量的聚乙二醇，共混体系相容性好，实现了热力学水平上的均相。

Introduced different molecular weight PEG in chitosan by solvent casting method , the blending system had good compatibility , reached homogeneous phase of the thermodynamic level .

本文利用三种聚甲亚胺的单体与尼龙6单体通过原位聚合反应，制备了三种聚甲亚胺/尼龙6原位聚合复合材料，制备工艺采用浇铸法。

In this paper , three different kinds of polyazomethines ( PAM ) / nylon 6 in situ polymerization composites were prepared using the process of monomer casting .

聚乳酸增塑剂要求高效、无毒、低渗出率等特点。本文选用了柠檬酸酯类增塑剂，通过溶液浇铸法，制备了PLA-4060D/柠檬酸酯和PLA-4032D/柠檬酸酯两种体系的增塑薄膜。

And requires plasticizers must be efficient , non-toxic , low migration rate , etc. In this work chose the citric ester , with the solution casting method , prepared PLA-4060D / citric ester and PLA-4032D / citric ester plasticized system as two kinds of film .

由熔融浇铸压制成形法与晶化、水热合成过程相结合，研制出用于牙面修复的cao-sio2-p2o5系统新型生物微晶玻璃。

Based on the cao-sio_2-p_2o_5glass system , a new glass-ceramic matieria used for den-tal Restoraion was developed through the glass melting , cast and press forming , and the combination processes of crystallization and hydrothermal synthesis .

在测试厚度方面，浇铸光片法优于投影法及粉末粘结法。

The improved method is better than theprojection method and the direct measurement of powder sample .