模锻

超高强铝合金等温模锻工艺

Ultra High Strength Aluminum Alloy Isothermal Stamping Process

模锻钛合金叶片锻件的新工艺

New Technology of Stamping Titanium Alloys Blade Forgings

抽油杆精密模锻工艺数据管理与CAD系统

Data Management CAD System of Oil Sucker Precision Forging

基于模糊PID的模锻液压机控制系统研究

The Study of Control System in Forging Hydraulic Press Based on Fuzzy PID

Al/Al2O3复合材料伪半固态触变模锻成形

Thixo-die-forging of Al / Al_2O_3 composite in pseudo-semi-solid state

锤上模锻CAPP系统的开发

Developing of CAPP system for die forging on hammer

在模锻工艺设计阶段，主要还是依靠技术人员的经验，对计算机辅助工艺过程设计&CAPP（ComputerAidedProcessPlanning）的使用很少。

The forging process design is mostly depended on the experience of technicians , but not the using of CAPP ( computer aided process planning ) .

VBA在齿轮坯闭式模锻CAPP中的应用

Application of VBA in Flashless Die Forging CAPP System for Gear Blanks

基于成组技术的液态金属模锻CAPP系统研究

The Research of CAPP System Based on GT for Design of the Forging of Liquid Metal

轴对称模锻过程的CAS系统

A computer aided simulation system for axisymmetric forging process

回顾和总结了热模锻工艺和模具结构设计CAD的研究现状，指出了目前存在的具体问题。

The state of the art in hammer hot forging process and die structure design is reviewed , the current issues are then summarized .

MDS图在液态模锻工艺过程单片机仿真控制系统中的应用

The Application of MDS Diagram in Monolithic Processor Emulating Control System for Liquid Metal Forging Technology

采用搅熔复合及半固态模锻法，研究了石墨颗粒增强Al基复合材料的制备工艺，并对石墨－Al基复合材料的强度、冲击韧性和耐磨性进行了试验研究。

The manufacturing process , strength , impact toughness and wear resistance of Al matrix composites reinforced with graphite are studied through melt stirring composing and semisolid die forging .

本文通过一种典型元素，详细说明了热体积模锻直长轴类锻件计算机辅助设计（CAD）中，截面面积计算的数学解析方法。

Through an analysis of a typical element , this paper introduces in detail a mathematic method to calculate the cross section area in CAD of straight long Shaft forgings .

STEYR转向节模锻成形工艺研究

Research on the technology of die-forging formation process for STEYR steering joint

选择了5T蒸汽-空气锤上开式模锻。

The open die drop forging with the 5 T steam - air hammer is selected .

本文用塑性成形模拟软件Deform-3D对多向闭塞精密模锻进行了模拟分析，验证了该工艺方案的可行性。

The model is simulated on the Deform-3D software and the closed die forging process is confirmed rightly .

不同温度的半固态模锻表明，材料能在较低压力下一步成形；SiC颗粒在加工后仍分布均匀，与基体结合良好；

Semi solid die forging at different temperatures was conducted , the results showed that the material could be shaped under low pressure , SiC particles still uniformly distributed after processing and combined well with matrix alloy ;

针对目前一些大型模锻水压机自动控制系统落后的现状，设计并开发了基于PLCS7-300的一万吨多向模锻水压机控制系统。

In view of backward situations of some large die-forging water press control system , a new control system of10000 ton multi-ram die-forging water press based on S7-300 PLC was designed and developed .

轴承钢（GCr15）液态模锻磨球的工艺实验研究

Experimental Research on squeeze casting process of bearing steel ( GCr15 ) abrasive ball Inner Mongolia Polytechnic University

深入分析了神经网络预测理论，结合模锻生产过程的特点和水压机计算机监控系统的结构，实现了基于BP神经网络预测模型的模锻过程质量控制系统。

The neural network predictive theory was researched deeply , and the quality control system based on BP neural network prediction model has been realized according to the characteristic of die forging process and the structure of the hydraulic press computer control system .

坯料的初始高径比不要超过2，否则容易出现双鼓型等缺陷。（4）通过VB等编程技术开发了模锻工艺优化平台软件，本软件对模锻工艺的优化起到了一定的帮助作用。

Original ratio of height to diameter can not excess two , or else , it will emergence double drum and other disfigurement . ( 4 ) Software of forge process optimize was developed base on VB programme .

采用300t压力机，对半固态ZL116合金进行了模锻成形实验。

Thixoforging tests on semi-solid ZL116 alloy were carried out using the300 T press machine .

在实验室条件下，采用不同液态模锻工艺参数对Al-Zn-Mg合金的成形性能进行了探索；

The different process parameters of liquid state forging were adopted to study the forming property of Al-Zn-Mg alloy under the laboratory condition .

主要研究了热模锻时坯料变形温度、变形量对Ti-1023合金显微组织和拉伸性能的影响。

The effects of heating temperature and deformation during hot-die forging on the microstructures and properties of Ti-1023 alloy have been studied .

实践表明，UBET用于模拟模锻过程的金属流动规律是可行的。

The experiments show that using UBET to Simulate the laws of the metal flow in drop forging was available .

并在利用原有设备的基础上将3t模锻汽锤改造为4.5t液压模锻锤。

The existent 3 t pneumatic die forging hammer has been transformed into ( 4.5 t ) hydraulic die forging hammer .

在分析了S195连杆螺钉传统的热模锻存在问题的基础上，指出该螺钉冷挤压加工的必要性。

On the basis of analysing existent problems in traditional production of link rod bolt with hot die forging technique , necessity is explicitly pointed out that link rod bolt is produced with cold extrusion technique .

介绍了康明斯6B柴油机曲轴在锻压机上的曲面分模直接模锻成型工艺。对工艺方案的确定及银模设计中的一些关键问题进行了分析。

This paper describes the forming process of crankshafts of Cummins 6B diesel engine by adopting a die with curved surface joint and direct die forging proeess on a forging press , then analyses some key points in the determinations of processing versions and designing of forging die .

结果表明，采用TZM钼基合金模具。在1050℃以接近10-3s-1的应变速率进行闭式模锻和开式模锻，模具材料均能满足使用要求，且开式模锻设备最大载荷不超过31×103kN；

The simulation results show that the molybdenum based die material ( TZM alloy ) can meet the practical need for both close die and open die forming when the disk is isothermal forged at 1050C with pseudo-constant strain rate of 10-3 s-1 ;