导向叶片

  • 网络Guide vane;turning vane
导向叶片导向叶片
  1. 工作于低功率工况的燃气轮机动叶片和导向叶片材料在600℃~75℃产生一种低温热腐蚀。

    The blade and vane materials in marine gas turbines operating under low power conditions suffered low temperature corrosion at 600 ° - 750 ℃ .

  2. 涡轮导向叶片是航空发动机的关键零件之一。

    Turbine guide vane is seen as one key part of the aero-engine .

  3. 以RBF神经网络为基础,提出了基于近似模型的编织复合材料涡轮导向叶片的结构与材料一体化优化设计方法。

    An integrated optimization design method of braided composites turbine guide vane based upon structure and material using RBF neural network model was proposed .

  4. 本文主要对K3合金导向叶片裂纹的清理及补钎进行了研究。

    The braze repair process of cracks in turbine guide vanes made from super-alloy K3 is investigated in this paper .

  5. 通过RNGk-ε湍流模型求解可压流的N-S方程,研究燃气轮机涡轮导向叶片尾缘劈缝出流冷气的流动情况。

    In order to investigate the flow characteristics of cooling flow downstream of a turbine guide vane trailing edge slot , numerical methods of RNG k - ε turbulent model were solved .

  6. 根据航空涡轮发动机与电厂燃气涡轮机(UGT)在尺寸、运转环境和负载要求方面的重大差异,讨论了UGT叶片和导向叶片用单晶合金的成分、力学性能和抗氧化与热腐蚀性能。

    In this paper , the composition , mechanical properties and corrosion / oxidation resistance of SC alloy for UGT blades and vanes are discussed according to the significant difference between aeroturbines and UGT in size , operating environment and duty requirements .

  7. 涡轮导向叶片过渡液相扩散连接工艺试验

    Testing for Transition Liquid Phase Diffusion Bonding of Turbine Guide Vanes

  8. 气膜冷却涡轮导向叶片流场数值模拟

    Numerical Simulation of Flow Field in a Turbine Stator with Film Cooling

  9. 具有可旋转导向叶片涡轮的振动实验研究

    Experimental research of vibration of the turbine with variable angle guide vanes

  10. 陶瓷导向叶片三维热应力有限元分析

    Three Dimensional Finite Element Analysis of Ceramic Turbine Stator Blade Thermal Stresses

  11. 导流板,流体导向叶片垂直筛板塔内催化剂筐式装填结构的流体力学研究

    Hydrodynamics of Catalyst Basket Packing Structure in the Vertical Sieve Plate Tower

  12. 涡轮导向叶片故障分析及其对策

    Analysis and Control for the Faults of Turbine Nozzled Blades

  13. 前置导叶预旋调节离心泵性能的数值预测与试验导流板,流体导向叶片

    Numerical Simulation and Experiment of Inlet Guide Vane Pre-whirl Regulation for Centrifugal Pump

  14. 某型发动机涡轮导向叶片故障探讨

    Discussion about faults of turbine nozzle vane of a certain type of engine

  15. 大型导向叶片铸钢件的数值模拟与工艺优化

    Numerical Simulation and Improvement of Casting Process for Large-scale Cast Steel Guide Vane

  16. 地面燃机涡轮叶片和导向叶片涂层的应用

    Application of Coatings for Gas Turbine Blades and Vanes

  17. 导流板,流体导向叶片循环流化床锅炉水冷壁防磨导流板的应用

    The circulation fluid bed boiler water cooling wall against rubs the air deflector application

  18. 导流板,流体导向叶片导向叶片热气防冰流动传热机理研究

    Mechanism Study on Heat Transfer and Flow of Hot Air Anti-Icing for Guide Vane

  19. 航空发动机可调导向叶片测量技术

    Measurement Technology of Adjustable Leading Vane of Aero_Engine

  20. 斜劈缝涡轮导向叶片尾缘出流气体流动特性数值分析

    Numerical Investigation of the Cooling Flow Downstream of a Turbine Guide Vane Trailing Edge Slot

  21. 导流板,流体导向叶片用可调进口导叶调节特性的大型混流泵

    Large Size Mixed Flow Pump with Characteristic Control by Means of Adjustable Inlet Guide Vane

  22. 多导向叶片式扩压器干式多片电磁离合器

    Multi-vane diffuser dry-type multidisc electromagnetic clutch

  23. 单级后置导叶轴流通风机内部流场数值模拟与优化导流板,流体导向叶片

    Numerical Simulation and Optimization for the Inner Flow Field of Single-stage Axial-flow Fan with Back Vane

  24. 叶轮间隙;叶片间隙;导向叶片与工作叶片的间隙凹槽叶顶非定常间隙泄漏流动和传热的数值研究

    Numerical study of unsteady tip leakage flow and heat transfer in a squealer tip blade impeller-diffuser clearance

  25. 空压机入口导向叶片与转速控制系统分析

    Guide-vane at the entrance of an air compressor and the analysis of the revolution speed control system

  26. 主要针对一级、二级镍基高温合金导向叶片的钎焊修复,进行了研究。

    Repair brazing of the first and the second stage vanes of nickel base superalloy was studied .

  27. 涡轮导向叶片变截面针肋通道内空气流动和传热过程数值模拟

    Numerical modeling of turbulent flow and heat transfer in a pin-finned convergent passage of gas turbine guiding vane

  28. 某发动机试车后,检查发现一片高压涡轮导向叶片排气边掉块。

    A piece of the first class high pressure turbine guide-vane fractured in exhaust edge after the engine test .

  29. 采用放大的叶片模型,利用大尺寸低速线性叶栅风洞进行实验,测量了涡轮导向叶片表面不同位置单排气膜孔喷射时下游的换热系数,研究了孔排位置、吹风比的影响。

    Film cooling heat transfer of single film row at different locations on turbine blade surface was studied experimentally .

  30. 为降低涡轮机的燃油消耗率,在民用动力装置的涡轮中广泛地采用了可旋导向叶片的结构。

    The variable angle guide vanes have been widely used for decreasing specific fuel consumption of the civil turbines .