允许偏差

GB/T15391-1994宽度小于600mm冷轧钢带的尺寸、外形及允许偏差

" Dimensions , shape and tolerances for cold-rolled steel strips with a width less than 600mm "

结论按照IAEA要求，该项比对的最大允许偏差为±1.5%，所以这次比对结果是合格的。

Conclusion The deviation of calibration factors between IAEA and SSDL should be no more than ± 1.5 % . Therefore , the result of this intercomparison is considered satisfactory .

边缘加工允许偏差应符合规范的规定。

Edge processing deviation should be allowed to meet the norms .

考虑沉桩允许偏差影响时碰桩验算的方法

Pile Collision Calculation Method when Considering Influence of Piling Allowable Variation

推荐安装质量要求及允许偏差，供参考。

Qua-oity requirement of installation and tolerence paratmeters are recommended .

现场焊缝组对间隙的允许偏差应符合规范的规定。

Weld scene deviation should allow the group to meet clearance norms .

混凝土保护层厚度施工允许偏差

Allowable Variation in Construction of Concrete Cover to Reinforcement

GB/T15945-1995电能质量电力系统频率允许偏差

Quality of electric energy supply & Permissible deviation of frequency for power system

螺栓孔孔距的允许偏差应符合规范的规定。

Bolt Hole Spacing should be consistent with the allowable deviation of norms .

GB12325-1990电能质量供电电压允许偏差

Quality of electric energy supply-Admissible deviation of supply voltage

GB/T16866-1997一般用途的加工铜及铜合金无缝圆形管材外形尺寸及允许偏差

Wrought copper and copper alloy seamless round tubes for general purposes-Dimensions and tolerances

GB/T3620.2-1994钛及钛合金加工产品化学成分及成分允许偏差

Titanium and titanium alloys & permissible variations of chemical composition for wrought product analysis

GB/T709-1988热轧钢板和钢带的尺寸、外形、重量及允许偏差

" Dimensions , shape , weight and tolerances for hot-rolled plates and sheets "

梁、、条的安装的允许偏差应符合规范的规定。

Beams and columns and purlines deviation should be allowed to meet the norms .

GB/T3194-1998铝及铝合金板、带材的尺寸允许偏差

Wrought aluminium and aluminium alloy sheets and strips & Tolerances on form and dimensions

检测实体混凝土保护层厚度允许偏差的商榷

Discussion on Allowable Variation in Measurement of Cover Depth to Reinforcement in Placed Concrete

摩擦系数范围包括允许偏差在内。

The friction coefficient includes the allowable tolerance .

ε：允许偏差率（%）。

ε: allowed deviation ( percent ) .

GB/T908-1987锻制圆钢和方钢尺寸、外形、重量及允许偏差

" Forged round and square steels & Dimension , shape , weight and tolerance "

GB/T222-1984钢的化学分析用试样取样法及成品化学成分允许偏差

Method of sampling steel for determination of chemical composition and permissible variations for product analysis

关于防波堤圆筒安装的允许偏差

Allowable Deviation about Breakwater Cylinder Installation

钢筋混凝土梁钢筋位置允许偏差标准探讨

An Exploration into the Allowable Deviation Limits on the Placement of Reinforcement in Reinforced Concrete Beams

对大量数据的精减，利用角度和弦高的最大允许偏差法进行点云精减。

A error limitation of angle and chordal highness method is used to filtrate clouding point .

GB/T905-1994冷拉圆钢、方钢、六角钢尺寸、外形、重量及允许偏差

" Dimension , shape , weight and tolerance for cold-drawn round , square and hexagonal steels "

钢屋架的垂直度和侧向弯曲的允许偏差应符合规范的规定。

Vertical and lateral bending of the steel roof of the deviation should be allowed to meet the norms .

压型金属板的尺寸及允许偏差、面质量、层质量等应符合设计要求和规范的规定。

Pressed metal plate size and allow deviation , surface quality , quality coating should comply with the design requirements and norms .

气割的允许偏差应符合规范的规定.机械剪切的允许偏差应符合规范的规定。

Deviation should be allowed to comply with the norms . The shear machine error should be allowed to meet the norms .

铝塑复合板、铝单板幕墙材料清洗与维护GB/T3194-1998铝及铝合金板、带材的尺寸允许偏差

The cleaning and maintaining of aluminum plastic composite panel aluminum panel curtain Wrought aluminium and aluminium alloy sheets and strips Tolerances on form and dimensions

与国标法实验对比，两种方法分析结果的相对偏差≤20%，在国家标准允许偏差范围内。

Compared with the national standard experiment method , the relative deviation between the two results is less than 20 % , which is under the national standard deviation ?

文中对6种典型变化情况进行了计算分析，从中确定滚道位置最大允许偏差范围，作为加工和测量时的控制值。

In this paper , 6 typical variation conditions are calculated and analyzed . The maximum allowable deviation range of raceway position is determining as a control value for machining and measuring .