轴瓦

轴瓦自激振动的诊断及几点消除措施

Diagnosis and some elimination measures about axle bush autoexcitation

每个轴瓦的流量采用调速阀进行调节，精确度高，互相干扰小。

The flow of each axle bush applies speed control valve to regulate , with high precision and low interference effect .

AlSn20/低碳钢复合轴瓦材料疲劳强度影响因素的研究

Factors affecting fatigue strength of Al-Sn 20 mild steel composite bearing

基于BP网络的Al-Pb-钢背轴瓦材料连铸工艺系统模拟

A BP Network-based Simulation of Al-Pb-Steel Bearing Material Continuous Casting Process

轴瓦厚度自动检测分选系统的PLC控制

PLC Control of Automatic Measurement and Grouping System for Bearing Thickness

讨论分析了AlPb合金轴瓦材料的烧结机理。

The sintering mechanism of Al Pb bearing alloy was discussed .

ISO薄壁轴瓦半圆周长检验模CAD程序系统

A CAD Programming System for ISO Thin-Wall Bearing Semicircular Perimeter Checkout Model

基于ARM核芯片的轴瓦壁厚/平行度自动检测系统

Automatic Testing System for Thickness / Parallelism of Bearing Pad Based on Chip with ARM Core

喷射成形钢/AlPb轴瓦合金复合板材的组织及耐磨性

Microstructure and Wear Resistance of Steel / Al-Pb Alloy Composite Strip Made By Spray Forming

提出了AlPb钢背轴瓦材料的连铸复合方法，设计研制了实现该方法的水平连铸复合装置。

A process and device of horizontal continuous composite casting was advanced to produce Al-Pb-steel backing bearing material .

Si3N4陶瓷轴瓦的疲劳磨损性能

The Study of Fatigue Wear Characteristic of Si_3N_4 Ceramic Bearing

用双辊连续铸轧方法制备了AlPb系轴瓦合金板材，铸轧工艺过程稳定，合金板成形良好。

Plate of Al Pb alloy was made by twin roll continuous casting , and the forming process was stable .

MC尼龙轴瓦的改性

The Modification of MC Nylon Axle Bush

DF4型内燃机车抱轴瓦碾瓦故障分析及改进

Grinding Tile Fault Analysis and Improvement on DF_4 Type Diesel Locomotive Axle Suspension bush

EMP复合材料轴瓦的蠕变计算

The Calculation of Creep Deformation of EMP Composite Bushings

通过研究烧结工艺对AlPb合金轴瓦材料显微组织及机械性能的影响，得出了较优的烧结工艺。

The effects of sintering process on microstructure and mechanical properties of Al Pb bearing alloy were studied and a suitable sintering procedure was determined .

依据对曲轴基体、轴瓦与涂层摩擦副匹配性能的分析，选择FeCSiAl作爆炸喷涂的粉末。

According to an analysis of the performance matching of the crankshaft body and bearing bush , Fe-C-Si-Al is selected as the powder for the explosive spray coating .

EMP轴瓦表层材料的表面形态结构分析

Analysis of Surface Morphology Structure of EMP Composites

采用宏微观检验、显微硬度测定、X射线衍射等方法对汽车发动机连杆轴瓦的失效进行了分析。

Macro examination , metallographic microscope , microhardness tester and X ray diffractometer were utilized to study the failure reasons for connecting rode bearing bush of automobile engine .

在实验研究基础上，提出了用PTFE（聚四氟乙烯）软带轴瓦替代巴氏合金轴瓦的问题。

Based on the experiment and research , this paper presents the advantages of using PTFE soft belt bearing shell to substitute babbitt metal .

Al-Pb系轴瓦合金的雾化沉积制备技术研究

Investigation on Spray Deposition Technology of AlPb System Bearing Alloys

托轮的接触疲劳强度设计锌合金完全可替代铜合金做4×60m回转窑托轮轴瓦材料。

Fatigue Design of Pads on the Rotary Kiln material of 4 × 60m rotating kiln .

300MW机组轴瓦振动原因分析及处理

Cause Analysis on Bearing Vibration of 300 MW Unit and its Solution

300MW汽轮机组轴瓦振动问题的探讨及处理

Discussion and Treatment on Vibration of Rotor-Bearing of 300 MW Steam Turbine Unit

发动机Cu-Pb轴瓦软镀层的扩散性能研究

Research on the Diffusibility of an Engine Cu-Pb Bearing with Soft Plating Coat

气雾化Al-Pb系轴瓦合金

Gas Atomization of Al Pb Bearing Alloys

水平连铸Al-Sn板坯制造铝钢轴瓦

Horizontal Continuous Casting of Al-Sn Billet for Manufacturing Al-Steel Axle Bushing

分析了影响EMP轴瓦表面油膜厚度的主要因素，给出了油膜厚度的一般表达式，实验证明：弹性金属塑料瓦必须进行瓦面修型；

This paper analyzed the main factors Which affected the oil film thickness of EMP thrust pad , giving the general equation of oil film thickness .

Al10%Pb钢背轴瓦材料过渡层为舌状组织结构，这种舌状过渡层组织由FeAl、Fe2Al5和FeAl3相组成。

The microstructure of transition zone of the bearing material was ligule-shape which was composed of FeAl , Fe_2Al_5 and FeAl_3 .

4×60M回转窑托轮轴瓦应用锌合金替代铜合金的可行性研究

The Studies of Zn - alloy Replacing Cu - alloy as Supporting Wheel Axle Bush Material of 4 × 60m Rotating Kiln