轴封

介绍了AMPS反应釜的设计，针对轴封采用磁力传动密封的特殊结构，指出了在设计和制造中应注意的问题。

The design of AMPS reactors was presented , some noticeable problems in design and manufacture were proposed for the particular structure using the magnetic driving seal in the shaft seal .

介绍了IHP型耐磨耐腐蚀稀硫酸泵过流部件材料的选择，结构及水力设计，轴封设计等。

He design of IHP weak sulphuric acid pump is described for material selection of flow passage components , structural and hydraulic features and shaft seal .

PVC浆料离心泵轴封系统技术改造

Technical reconstruction of shaft seal system for PVC slurry centrifugal pump

介绍了对PVC生产过程中产生的母液水、蒸汽冷凝水、轴封水、废水与冲洗水的回收利用工作及取得的经济效益。

The reutilization of water in PVC production were introduced , including mother liquid ; steam condensate , seal water ; waste water and wash water .

某电厂引进型300MW汽轮机轴封系统改造及分析

Reconstruction and Analysis on Gland Sealing System of 300 MW Steam Turbine

2MCL型压缩机轴封系统的改造MCL型水基合成切削液的研制

THE IMPROVEMENT OF 2 MCL COMPRESSOR SEALING SYSTEM Preparation of MCL Water - Based Synthetic Cutting Fluid

600MW机组高压缸轴封漏汽定量分析

Quantitative Analysis of Steam Leakage through the Gland Seal of 600 MW Steam Turbine

国产引进型300MW汽轮机轴封系统的试验研究

Testing and Research of Shaft Sealing System of Indigenous Imported Type 300 MW Steam Turbine

200MW汽轮机轴封压力控制系统改造

Retrofit of Shaft Seal Pressure Control System of 200 MW Turbine

轴封自密封系统在国产200MW机组上的应用

Application of Self-sealing System of Shaft Gland to Domestic 200 MW Unit

200MW汽轮机轴封系统运行状态的在线监测

On-line Monitoring the Operating Condition of 200 MW Steam Turbine Gland System

660MW机组轴封系统结构与运行分析

Analysis of structure and operation of shaft gland seal system in 600 MW unit

VISO系列的轴封的选择范围很广。

The range of choice of VISO series shaft seal is wide .

BM-20Д2型排粉机轴封漏粉改造

Powder Leakage Transformation of the Shaft Seal of Powder Exhauster of BM-20 Д 2 Type

以一台300MW汽轮机组的调节级静叶栅为研究对象，就轴封漏汽对叶栅二次流及出口流场的影响进行了数值模拟。

In this paper the effects of gland leakage on the secondary flow and outlet flow fields in the governing stage stator cascade of a300MW turbine set are simulated numerically .

PWF主要由泵盖、泵壳、叶轮、轴封、轴、和托架等零部件组成。

PW , PWF mainly by the pump cover , pump casing , impeller , shaft seal , shaft , and bracket the composition of such components .

稍晚的主泵轴封泄漏则将压力壳下封头损坏的时间推迟约3000s。

Contrarily , the vessel breach is predicted to be delayed about 3000 s by later RCP seal leak .

通过对9E联合循环汽轮机轴封系统的现状分析，提出对轴封溢流的改造以达到节能降耗的目的。

Through the status analysis on shaft seal system of 9E combined-cycle steam turbine , the improvement for shaft seal overflow is put forward to save energy and reduce consumption .

针对田家庵发电厂波兰产的1号、2号（TK-120）汽轮机的现运行情况，实施了对汽轮机中压缸、转子及轴封系统的改造工程。

The IP cylinder rotor and gland-packing system of No.1 , No.2 TK-120 steam turbine has been modified according to its operation in TianJia'an power station .

泵体部分的轴封为两套串联的机械密封，上部机械密封代号为60B，下部机械密封代号为60A。

Pump body seal part of the series for two sets of mechanical seals , mechanical seal , code-named the upper part60B , the lower mechanical seal , code-named60A .

也可以采用Rheoseal密封，它在轴封内表上加工有反向螺旋槽，可使聚合物被反压回到进口。

Also , it can be used in Rheoseal seal shaft sealing in a table , can make the reverse spiral groove back by the import of polymer .

文中分别对轴封漏气、供热抽汽、小汽轮机用汽、再热减温水、高压门杆漏汽等的热经济性分析分项进行了叙述，并以300MW机组额定工况的数据进行了验算。

Thermal economy analysis and the classification are given for the gland-packing leakage , extraction steam for heating , the steam for the auxiliary turbine , desuperheating water of reheater and the high pressure valve leakage . Based on a 300 MW unit , its economic load parameters are calculated .

针对200MW汽轮机组轴封供汽压力控制及汽轮机轴端在运行中存在冒汽和油中带水、空气内漏等问题进行了原因分析，对改造方案的设计及实施做了详细介绍。

This paper makes reason analysis pointing to the problem of shaft seal steam supply pressure control of 200 MW turbine sets and vaporizing , water in oil and air inner leakage existed in operation of turbine shaft-end , introduces in detail about design and implement of retrofit scheme .

防止所有漏水，因为它没有轴封设备。

Prevent all leakages since it has no shaft seal equipment .

浓氨水泵柔性石墨轴封的试验研究

Testing Research on Flexible Graphite Shaft-seal of Thick Liquid Ammonia Pump

轴封供汽量对机组经济性影响的分析

The Analysis of Shaft Seal Steam on Unit 's Economic Benefit

活塞压盖式填料轴封新结构关于填料压盖式轴封设计方法的建议

A New Construction Shaft Seal Suggestions on Design of Packing Glands

圆盘反应器轴封结构及改进措施

The shaft-sealing structure of the disk reactor and the improving measures

排粉机轴封漏粉原因及处理

Cause and Handling of Pulverized Coal Leak at Exhauster Shaft Seal

输蜡器轴封结构改造

Reform of Axial Seal Structure in the Device of Transportation Wax