隔膜阀

相对发达国家而言，我国气动隔膜阀阀门行业还比较落后。

Relative to the developed countries , China 's pneumatic diaphragm valve valve industry is still lag behind .

推荐的开启程序：从彻底打开到关闭，隔膜阀手轮旋转大约11/4圈。

Recommended Opening Procedure : The diaphragm valve handwheel rotates about 1 1 / 4 turns from fully open to closed .

可提供PVC，CPVC和玻璃纤维填充聚丙烯作为隔膜阀多样性的材质选项。

Available in PVC , CPVC and Glass Filled Polypropylene with a variety of Diaphragm material options .

并对精益生产的适用性进行分析，认为精益生产不仅可以应用到JT公司隔膜阀衬胶阀体生产车间，同时也可以应用到其它产品、其它企业。

Analyze the applicability of lean production , Lean production can use not only on caliber of diaphragm valve rubber lining body of JT Company , but also other products and other company .

不能在现场修理或调整隔膜阀。

Diaphragm valves cannot be repaired or adjusted in the field .

进口隔膜阀是一种特殊形式的截断阀。

Import boxes are a special form of cut-off valve .

隔膜阀膜片的研制

Development of Membrane for Diaphragm Valve

运转原理：束缚隔膜阀是采用通过横膈膜连接的两个阀杆的手轮型阀门。

Operating Principle : The tied-diaphragm valve is a handwheel-operated valve , utilizing a two-piece stem connected through the diaphragms .

对于真活接球阀、止回阀和隔膜阀，在上底漆和粘固剂连接之前，先拆卸活接头螺母和端口连接件。

On True Union Ball , Check and Diaphragm valves , remove union nuts and end connectors before priming and cementing connections .

我们知道，目前除了蝶阀和隔膜阀在结构上完全对称外，所有其他结构的调节阀都是不对称的。

We know that , with the exception of butterfly valve and the valve is completely symmetrical in structure , all other structures are asymmetric valve .

当开启隔膜阀的时候，在大约一圈中，你会感觉到阻力，到了一圈时，大部分或所有阻力都会消失。

When opening a diaphragm valve , you will feel resistance for approximately one turn , at which point most or all resistance on the handwheel will disappear .

介绍隔膜阀膜片的研制情况，阐述隔膜阀膜片的卫生质量要求、配方设计特点和生产工艺要点。

The development of the membranes for diaphragm valves was presented . The quality requirement for health , characteristic of formula design and key point for process were reviewed .

根据结构特点有挡板阀、插板阀、蝶阀、球阀、隔膜阀、角阀、直通阀、三通阀。

According to structural characteristics of a flapper valve , flapper valves , butterfly valves , ball valves , diaphragm valves , angle valves , through the valve , three-way valve .

更多种人造合成橡胶和工程塑料的应用，以及更广泛地选择阀体衬里材料，使隔膜阀在现代工业的各个领域都得到广泛的应用。

More kinds of synthetic rubber and engineering plastics applications , and a wider selection of body lining material to diaphragm valves in the various fields of modern industry have been widely used .

本文介绍一种由双喷嘴侧射流流量测量机构、隔膜阀控制机构、防窃水结构、IC卡和单片机系统组成的一体化IC卡水表。

This paper introduces a kind of principle of flow measurement that adopts siding structure efflux with double spray nozzle and magneto-electric transformation , which uses diaphragm valve and water steeling-proof to compose integration of IC card water current meter by IC card and monolithic processor .

设计制造出一种正压气动隔膜界面阀，取得很好使用效果。该阀耗气量不足1L，延时不到1s。设计了扇形阀和管夹阀两种新型真空界面阀，分析了各自优点。

Its air consume is less than 1L , while time delay is no more than 1s . Two kind of new vacuum interface valves such as fan-shaped valve and tube clamp valve has been designed , of which the merits are analyzed .

四通隔膜导阀用于所有双作用气动缸体执行器上。

Four-Way Diaphragm Pilot Valves are for use on all double-acting pneumatic cylinder actuators .

利用MATLAB软件仿真出隔膜泵排出阀的运动规律，直观地观察并总结排出阀的运动情况。

There is emulation of the pump valve ' motion regular by MATLAB ;

ZPM11×20×1250隔膜泵单向阀损坏原因分析及措施

Analysis to the Damage Cause of Check Valve in ZPM11 × 20 × 1250 Membrane Pump and the Measurement

流体动力角式隔膜排泥阀的设计

Design of the mud valve of angle type with fluid power

隔膜泵自动阀的研究

The research on the valve of diaphragm pump

进口气动隔膜式调节阀的检修

Repairing of imported pneumatic diaphragm regulating valve

本文完成了隔膜泵单向阀声发射信号的采集监测与分析研究。

The paper completed the acquisition monitoring and analysis for acoustic emission signals of one-way diaphragm valve .

拆卸阀盖和隔膜。安全阀活塞总成可以笔直提出到外面来。

Remove the cover and diaphragm . The relief valve piston assembly can be lifted straight up and out .

高压隔膜泵进出料阀的改进

An Improvement on the Inlet and Outlet Valves of High Pressure Diaphragm Pump

泥浆隔膜泵加装节流阀的节能试验

An Energy-Saving Test on the Slurry Diaphragm Pump by FiXing Flow Regulating Valve

隔膜阀体流通平滑、节流元件为弹性隔膜阀，阀盖上无填料函。

Diaphragm valve body flow smoothly , cutting components for the elastic diaphragm , valve cover stuffing .