锭模

低合金铸铁粗铅锭模的试验

Test of Raw Lead Ingot Mould Made of Low-Alloy Cast Iron

换底锭模在铁合金浇注中的应用

Application of bottom change-over ingot mould to ferroalloy casting

对Al－4.5%Cu合金在纯石黑坩埚中用卤盐熔剂净化后的过冷度及其在金属锭模中的凝固组织特征进行了研究。

The undercooling and structure of the Al-4 5 % Cu alloy denucleated by the chloride flux in a fine graphite crucible is studied in this paper .

同时，利用华铸CAE软件对钢锭模的充型及凝固过程进行模拟计算，优化钢锭模的铸造生产工艺。

Meanwhile , the simulation of mold filling and solidification is conducted to meliorate the manufacture technique of ingot mould based on the software of HZ-CAE .

底注钢锭模设计及特种Cr-Ni、Cr-Mo钢锻件的试制

Design of Bottom Pouring Steel Ingot and Forging Manufacture of Special Cr Mo and Cr Ni Steels

主要介绍太钢2.8t八角整体锭模的设计参数以及初步试验结果。

This paper discussed the design - parameter of octagon solid die and its result of experiment .

运用冲天炉熔炼试制QT400-18球墨铸铁，作为锌锭模的材质，提高锌锭模使用寿命。

To use pick cupola smelting triM-produced QT400-18 ductile iron , zinc ingots module as material , improve zinc ingots mode using life .

因钢锭模表面生成气体而形成的表面针孔。

Surface pinholes caused by gas formed at the mould surface .

锭模是铸造生产过程中重要的设备。

Ingot moulds are important equipment in the production process of casting .

厚大断面球铁钢锭模铸造质量分析

Quality analysis of large section mould from nodular cast iron

机头流道的三维实体造型研究八角整体锭模的设计与初步试验

Die cave 3-D solid modeling Design and Experiment of Octagon Solid Die

基于数值模拟的锌锭模应力应变分析

Stress-strain Analysis of Zinc Ingot Die Based on Numerical Simulation

球铁钢锭模设计的改进

Improvement on Design of ingot mould of nodular cast iron

换底锭模的设计与生产

Design and Production of Changing the Bottom of Ingot Mould

国产复合岩棉板在生产储油船上应用上小下大钢锭模挂绝热板生产船板钢

Shipbuilding plate production using small top large bottom mould with insulating plate

八角整体锭模的设计与初步试验

Design and Experiment of Octagon Solid Die Die cave 3-D solid modeling

影响锭模寿命结构因素的研究

Investigation for the Main Factors Affecting Ingot Mold Life

锌锭模制造问题探讨与研究

Study on Several Problem of Zinc Ingot Mold Production

钢锭与锭模在钢锭凝固过程中应力分析的研究

Research on transient stress fields in ingot and mold during solidification of ingot

钢锭与锭模三维应力场耦合分析有限元系统

Three Dimensional Finite Element Analysis System for Stress Fields of Steel Ingots and Molds

熔模铸造高强度锑铸铁镉锭模

Permanent Mould for Cadmium Ingot Casting Made of High-strength Sb Cast-iron With Precision Casting

改进锭模系列和锭型结构提高钢材成材率

To increase the yield of hot-rolled plate by improving ingot mould configuration and series

锭模结构及浇注工艺对钢锭内部缩松的影响

Influence of Mold Geometry and Pouring Process on Porosity and Shrinkage Cavity in Steel Ingots

小型镇静钢锭模的设计与应用

Design and application of small killed ingot

中小型稀土镁球铁钢锭模的性能及使用寿命分析

The properties and service life analyses for middle and small-sized RE-Mg ductile iron ingot mold

提高中锰低硅钢锭模质量研究

The Research on the Quality Improvement of the Medium Mn and Low Si Steel Ingot Mold

介绍了铝热焊修复钢锭模的工艺过程。

The procedure of thermit welding for repair of the ingot die is presented in the paper .

阳极板浇铸机锭模小车运行机构润滑方式的选择

A Choice of Lubrication Mode for Running Mechanism of Ingot Mould Bogie of Anode Plate Casting Machine

单位铁水消耗的锭模费用可降低75%。

The charge of ingot mould of cost of unit molten iron can be reduced by 75 % .

有限元分析结论表明锭模应力场与温度场存在明显的对应关系。

Corresponding relationships between the temperature field and stress field in ingot mold was revealed by FEM analysis .