误差极限

该系统的实测误差极限小于0.3°。

The limit of mismatch error is less than 0.3 ° .

提及的是核监测仪器的工作误差极限，亦即仪器测量的不确定度。

This paper introduces the limits of operating errors of nuclear monitoring instruments .

误差极限值的综合方法

The Combination Method of the Limit Values of Error

车架铆装线系统误差极限的确定方法

Determination of Systematic Error Limit in Producing Frames on A Riveting and Assembling line

天文测量误差极限：参考星位置对应的最大误差，用角秒表示。

Astrometric Limit : The maximum residual in the place of a reference star , specified in arc seconds .

静态标定曲线的精度为±0.24%wt，动态考核误差极限<0.5%wt，已能满足混凝土生产的要求。

The precision of the static state calibration curve is 0.24 % wt. The error limits of the dynamic state check are < 0.509 % wt. It has satisfied the demands of the concrete production .

Hazard函数估计误差的极限定理

A Limit Theorem for Error of the Failure Rate Estimators

当这些措施都被采用后，在进行单次交流功率测量时，可使由热电变换器引起的交、直流转换误差的极限值（≈2.5σ）小于10ppm。

After all these improvement methods to be adopted , the limiting value (≈ 2.5 σ) or the AC / DC transfer error caused by thermal converter will be less than 10 ppm in AC power measurement with single time .

文研究了插补原理中走步误差最低极限为1／2步；

The step error of the Interpolation Theorm is explored in this paper . The lowest limit is 1 / 2step ;

建立了基于距离空间聚类和基于随机采样两种区域划分算法，并且给出了圆心初值误差的极限。

Two algorithm for region partition based on distance space clustering and random sample are found . The limit of initial value error is given .

摩擦环节对伺服控制系统性能造成的不良影响，主要体现在能够引起位置误差、极限环、爬行等现象的发生，这是提高运动控制精度的一个障碍。

Friction may cause bad performance of control system , which embody phenomenon such as the position error , limit cycle , stick-slip etc. So it is an obstacle to improve the kinematic control accuracy .

系统分析了影响单计量光栅位移测量系统精度的各种因素，定量计算了各项误差的极限值，并分别提出了误差的修正补偿方法。

The factors that influence the measure precision are systematically discussed in single metrology grating ( SMG ) system . The maximums of all kinds of errors are calculated and corresponding correction and compensation methods are provided .

提出了各采样点示值数据图形相对于评定基线不同分布时的直线度误差的极限误差的分析计算方法，给出了计算实例，并得出了相应的结论。

It puts forward the analysing and calculating method of the limiting error of straightness error when the figure of sampling data is differently dispersed relative to datum line , and gives some examples of calculating and draws a final conclusion .

多变元非参数密度估计的平均均方误差的中心极限定理

Central limit theorem for averaged square error of multivariate non-parametric density estimators

论测量误差与验收极限

On the measurement error and the limit of acceptance

条件密度双重核估计的积分均方误差的中心极限定理

Central Limit Theorem for Integrated Square Error of Double Kernel Estimators of Conditional Density

利用随机误差的按极限误差合成的方法对微小型零件的装配误差进行了合成计算。

Assembly errors were calculated based on the theory of random error synthesis according to limit error .

其三，模糊控制的控制精度不高，主要原因是模糊控制的稳态误差和零点极限环振荡问题，这一缺陷直接制约了其在高精度控制领域的应用。

Third , the fuzzy control 's precision is not high . The main reason is the fuzzy control static error and the zero vibration , which has directly restricted it in the high accuracy control domain application .

坦克炮控系统存在低速摩擦，摩擦环节不但造成系统的稳态误差，而且导致极限环振荡、低速爬行等现象。

The phenomena such as low speed friction , system steady-state error , limit cycle oscillation , and static-slip caused by the frictions exists in gun control system of tanks .

转台伺服系统中摩擦环节的存在容易导致系统出现稳态误差、爬行、极限环振荡等现象，严重影响了转台性能的提高。

However , the presence of friction in servo system results in the steady-state error , crawls , and limits cycle oscillation , and seriously impact on improvement performance of turntable .

讨论了对误差的来源和误差的合成，推荐了固有误差极限与变动量极限的合成以及影响量误差极限的合成为工作误差极限的两个计算公式。

The text analyses relative intrinsic errors and relative variations under different influence quantities , gives calculating formula for the limits of operating errors .

这从理论上，为误差的来源找到了根源，也给出了线性插值的误差的理论极限。

This reveals the source of the error and gives a theoretical error limitation of linear interpolation .