蚀坑

通过对硅和铝的刻蚀实验，研究在溅射刻蚀与增强刻蚀方法下刻蚀速率、蚀坑形貌与离子束流大小的关系。

The variation in etch rate and crater topography with ion current have been investigated .

放电单脉冲的电流峰值和脉宽决定了单个电火花蚀坑的大小和深度，从而直接决定了工件的加工表面粗糙度、形状精度和尺寸精度。

The peak current and pulse duration of single pulse determine the size and depth of discharge crater , so they determine the machining surface roughness and size and shape accuracy .

蚀坑法研究微量Ce及退火对高纯铝箔立方织构的影响

Pit Etching Research about Heat Treatment and Ce Content on Cube Texture in High Purity Aluminium Foils

本文介绍了用X射线和蚀坑方法研究含MnS-AlN为抑制相的3%Si-Fe合金形变和初次再结晶织构。

The deformation and primary recrystallization texture in a MnS-AlN-inhibited 3 % Si steel has been investigated by X-ray diffraction and etching pits technique .

这说明富Cd原料的改进布里奇曼法可以生长出低蚀坑密度的CZT单晶体。

It is demonstrated that the Cd-riched starting materials can grow low EPD CZT single crystals by modified Bridgman method .

给出了KTP（110）面上的蚀坑图形和位错密度。

The etching pits and the dislocation densityon ( 110 ) plane of KTP crystals are given .

设计了利用KOH溶液定向腐蚀制作出的平行四边形蚀坑串，所形成的锯齿状沟槽结构来固定光纤。

The dentate groove is devised which is composed of a series of the etched parallelogram pits in KOH solution .

采用蚀坑法、EBSD微取向分析和X射线法等手段，对稀土电解电容器用铝箔制备过程中的织构演变规律进行了研究。

The evolution rule of the rare earth aluminum capacitor foil preparation process was investigated by means of bit etching , EBSD micro orientation analysis and X-ray method .

利用自行改装的XJ－16型金相显微镜测量了核承压设备堆焊层AISI308不锈钢材料的蚀坑深度。

The depth of pitting occured in AISI 308 stainless steels is measured by using the modified XJ 16 metalloscope .

实验表明大量的（100）晶面，适量的位错蚀坑、低杂质含量尤其是Fe元素量是提高高压铝箔比容的关键因素。

It is shown by experiment that large number of ( 100 ) crystal face , proper dislocation etching pits and low content of impurity especially Fe element are the key factors influencing on specific capacitance of high voltage capacitor foil .

考虑到GaAs单晶的极性对器件工艺的影响，本文提出了一种由位错蚀坑的形状确定极性，在单晶锭上作两个参考面的方法，以保证衬片方位的一致性。

Considering the effect of GaAs polarity on the device technology , two reference faces were prepared on sides of GaAs ingot by means of the shape of dislocation etch-pits to ensure the consistency of wafer orientation .

该项技术采用高强度、耐腐蚀的PCE涂敷材料填充管壁蚀坑，形成厚达3～6mm的复合衬里。

This technology uses high strength , corrosion-resisting PEC coating material to fill with corrosion pit on pipeline and forms a 3 ~ 6 mm compound lining .

通过比较阴极斑点蚀坑的大小和分布，分析了CuCr触头材料显微组织中Cr相尺寸的大小对阴极斑点运动和蚀坑形貌的影响。

The microstructure analysis showed that the CuCr alloys has an important effect on the discrimination , in which the size of Cr phase plays an main role in effecting the moving direction and distribution of cathode spot craters .

测定了Ni~（2+）：MgF2晶体的吸收和荧光光谱，初步观察了晶体的光学均匀性、应力和蚀坑密度。

The Absorption and fluorescent spectra of Ni ~ ( 2 + ): MgF_2 have been measured , and optical homogeneity , stress and etching pit density are primarily examined .

首次用原子力显微镜给出了用两种腐蚀剂腐蚀过的KTA晶体表面的铁电畴和位错蚀坑的照片及定量信息，如发现铁电畴的明区要高于暗区，且两者的粗糙度明显不同。

The pictures and quantitative information on ferroelectric domain and etch pits of dislocations in etched KTA crystal surface have been given first time by atomic force microscope .

由于[0001]方向的螺型位错的Burgers矢量比刃型位错的Burgers矢量大得多，故可从蚀坑的深浅来判别螺型位错和刃型位错。

Because of the Burgers vector of the screw dislocations in [ 0001 ] direction are much larger than that of the edge dislocations , one can distinguish the screw dislocations from the edge dislocations according to the depth of etch pits .

微观分析表明，腐蚀形貌呈蜂窝状，其蚀坑深度约为130μm。

The depth of the corrosion was about 130 μ m.

工业铜单晶线材浸蚀蚀坑的研究

Study on the Etch Pits of Copper Single Crystal Wires

蚀坑法测定铝合金板材织构

Determination of the Texture in Aluminum Alloy Plate with Pit - etching Method

硫镓银晶体（112）面蚀坑形貌研究

Study on Etch Pits Morphology on the ( 112 ) Face of AgGaS_2 Crystals

蚀坑的形成条件及其几何多样性

Forming conditions and geometrical variety of etch figures

蚀坑法研究冷轧及退火工艺对无取向硅钢织构演变的影响

Pit etching research about rolling and annealing treatment on texture in non-oriented silicon steel

测定面织构的金相蚀坑法

Determination of texture by etch figure method

一种预测蚀坑腐蚀疲劳寿命的概率模型

Probabilistic method of pitting corrosion fatigue life

面心立方晶体表面蚀坑的分形特征

The Fractal Geometric Properties of Etch Pits on ( 111 ) Surface of Face-Central Cubic System

体心立方金属的蚀坑性质及其晶体位向的定量分析技术

The etch-pits feature of BCC metals and analytical technique for quantitative determination of their grain orientation

疲劳裂纹易于在微动区，特别是在蚀坑处萌生和扩展。

Fretting fatigue crack initiation tended to occur in fretting scar , especially from grinding pits .

碲锌镉单晶体的（110）面蚀坑形貌观察

Observation on Etch Pits on the ( 110 ) Faces of Cd_ ( 1-x ) Zn_xTe Crystals

的两种铝箔进行了多种退火处理，利用蚀坑法分析统计了热处理后铝箔的立方织构含量。

After varying the annealing treatment , the cubic texture of aluminium foils with Al content of99 .

依据硅的各向异性腐蚀特性对平行四边形蚀坑尺寸进行了分析设计。

The size of the parallelogram is analyzed and designed according to anisotropic etching properties of silicon .