聚合反应工程

由于反应体系复杂，聚合过程模型化已成为聚合反应工程的一个重要发展方向。

For its complexity of kinetics mechanism , simulation of polymerization process become a major branch of polymer reaction engineering .

聚合反应工程新进展

Recent progress in polymerization reaction engineering

己内酰胺聚合反应工程CAD软件包&Ⅰ.工业化生产实际值与软件包计算结果的比较

CAD software for CPL polymerization engineering & ⅰ . comparison between calculation results and practical results

在此基础上，提出了PA6聚合反应工程研究中尚有待开展的几点建议。

And then , a few problems for the further research in PA6 polymerization process are pointed out .

从聚合反应工程角度分析了顺丁橡胶（BR）生产中的聚合过程特点及其偏离理想动力学的情况。

The process characteristics of polymerization reactor for butadiene rubber ( BR ) production were analyzed in view point of engineering research .

介绍了己内酰胺聚合反应工程CAD软件包的建立，用工厂单VK管聚合和两步法聚合生产工艺验证了该软件包的可靠性。

A new CAD software for caprolactam polymerization was reported . Its reliability was verified by the results from plants with single VK tube polymerization or two step polymerization .

强调要实现sPP的工业化，尚需从聚合反应工程的角度，加强催化剂负载和聚合工艺的研究。

Confronting with problems such as low bulk density of sPP and reactor fouling , it has been emphasized that the studies of reaction engineering focused on developing an optimal process for catalyst support and special polymerization process are very important .

氯乙烯悬浮聚合反应工程中的若干问题

On the of Reaction Engineering in the Suspension Polymerization of Vinyl Chloride

顺丁橡胶聚合反应工程分析与生产装置技术改造探讨

Engineering analysis for polymerization and approach to improving process equipments in BR production

聚合反应工程的进展及应用

The Development and Utilization of Polymer Engineering

研究了改革课程教学，因材施教，因人施教，重视实习和实验教学对提高聚合反应工程教学质量的影响；

The effects of teaching reform , teaching students according to their aptitude , paying attention to laboratory and practice on improving the quality of polymerization engineering teaching were studied .

锂系聚丁二烯橡胶间歇聚合反应釜工程研究

Engineering Study on Non-continuous Reactor of Polybutadiene with Lithium Catalyst

环氧丙烷开环聚合反应的工程研究（Ⅱ）间歇和半连续操作时聚醚的数均分子量和双键度

Investigation of ring opening polymerization of propylene oxide (ⅱ) average molecular weight and degree of unsaturation of polyols under batch and semicontinuous operating conditions

自由基聚合在聚合反应工程中占有举足轻重的地位，在自由基聚合反应过程中，尤其是本体聚合，常常出现凝胶效应和玻璃化效应。

Free radical polymerization plays a key role in modern polymerization reaction engineering .

由于聚合反应体系本身的复杂性和装置工程特性的综合性，决定了聚合过程模型化尤其是与工业装置紧密结合的聚合过程模型化既是聚合反应工程的一个重要发展方向，又是一个难题。

Due to its complexity of the polymerization kinetics mechanism and the practical industrial polymerization processes , modeling of a polymerization process becomes a major branch of polymer reaction engineering , and it 's also an unsolved and challenging problem .

由于乳液聚合过程非常复杂，聚合釜的建模是聚合反应工程中的一个难点。

Since latex polymerization course is very complex , modeling of polyreactor is a difficulty in polyreaction engineering .