耐磨性

外掺物对水泥混凝土路面耐磨性的影响

The Effect of Additive Material on Wearing Quality of Cement Concrete Pavement

改性后的高分子皮结具有耐磨性好、抗冲击力强、噪音小、使用寿命长等优点！

After modification , the macromolecule filling piece has the advantage of good wearing quality , good shock resistance , low noise , and long performance life .

Al及Al合金离子注入氮层组织结构及其耐磨性

Structure and wear behaviour of Nitrogen-Implanted aluminum alloys

离心-SHS法制备Al2O3复合陶瓷及耐磨性研究

Study of Al_2O_3 Ceramic Composite by Centrifugation-SHS and Abradability

通过组织分析认为，表面渗层耐磨性较高的主要原因是SiC颗粒对基体硬度的提高作用及本身作为高硬抗磨颗粒提高耐磨性的作用。

The causes of high wearability was SiC particle and surface layer .

但是PC易应力开裂，耐候性、耐磨性较差。

However , PC suffers easy stress cracking , bad weather resistance and poor abrasion resistance .

NiSi3N4复合电镀工艺与耐磨性研究

Research on Processes and Wear Resistance of Electroplated Ni-Si_3N_4 Composite Coatings

纳米稀土La2O3对Ni基合金喷焊层组织和耐磨性的影响

Effect of Nanometer Rare-earth La_2O_3 on Structure and Abrasiveness of Ni-based Alloy Spray-welding Coating

喷射成形钢/AlPb轴瓦合金复合板材的组织及耐磨性

Microstructure and Wear Resistance of Steel / Al-Pb Alloy Composite Strip Made By Spray Forming

烧结温度对WC增韧Al2O3陶瓷耐磨性的影响

The Influence of Sintering Temperature on Wear Resistance of Al_2O_3 Ceramics Toughened by WC

CVD涂层硬质合金刀具的耐磨性和破损特性

Characteristics of wear resistance and fracture of CVD coated carbide tools

而镀层中的SiC硬质粒子提高了镀层的耐磨性。

At the same time , the SiC particles can improve the wear resistance of the coating .

合金元素Ni、Mo、W及熔渗铜对烧结钢耐磨性的影响

Influence of alloy elements Ni 、 Mo 、 W and copper infiltrated on wear resistance of sintered steels

当表层中γR量稍低于42%时，其耐磨性最佳。

When the content of retained austenite is a little less than 42 % in the layers , its wear resistance is optimum .

随着VC含量增加，高钒系合金的耐磨性迅速提高。

However , the relative wear resistance increase rapidly with increasing the VC content in high vanadium alloys .

RE，Al复合变质处理可使铬钨合金白口铸铁的硬度、冲击韧度、耐磨性都得到提高。

The hardness , impact toughness , wear resistance of the high chromium casting iron containing wolfram by RE-Al modification treatment are all improved .

TiAl合金激光表面合金化涂层的组织与耐磨性

Microstructures and wear resistance of laser surface alloyed composite coatings on TiAl alloy

TiC质量分数为50%时，熔覆层具有最佳耐磨性。

The coating possesses optimal wear resistance when the mass fraction of TiC is 50 % .

利用对比试验，运用扫描电子显微镜、能谱仪和XRD等手段对VCFe基表面复合材料的耐磨性做了初步的分析研究。

Wear resistance of VC Fe base surface composites was studied by means of SEM , EPMA , XRD with comparative experiment .

通过常压烧结制备了Al2O3/Y-TZP复相陶瓷，研究了Al2O3含量对材料力学性能及耐磨性的影响。

Al_2O_3 / Y-TZP composites were prepared by pressureless sintering . Effects of material composition on mecha ?

测定并分析了用PCVD法获得的TiN涂层内的残余应力、涂层的抗变形性以及涂层的耐磨性。

Residual stresses , deformation resistance and wear resistance of PCVD TiN coating are determined .

当粉芯中WC质量分数超过25%后，涂层的耐磨性有所下降；

The abrasive wear resistance of the coating reduced when WC content was more than 25 % .

进行Ni-P-纳米金刚石非晶态复合镀层的晶化转变过程、及其硬度和耐磨性等的研究，并与Ni-P化学镀层、Ni-P-微米金刚石复合镀层的性能进行比较。

The electroless process and structure transition and properties of Ni-P-nano-diamond composite coating were systematically investigated .

结果表明，（Ti，Al）N膜兼有硬度高、韧性好、应力小的优点，从而保证了良好的耐磨性。

The results show that the ( Ti , Al ) N coating is of high hardness , good toughness and small stress , which provides excellent wear-resistance .

Cu的作用与Ni基本相同，材料最好的耐磨性和耐蚀性出现在Cu含量为3%处。

The function of Cu is the same as that of Ni , and wear resistance and corrosion resistance are optimum when Cu content is 3 % .

Si3N4是一种良好的复合共沉积粒子，具有硬度高、耐磨性好、性能稳定等特点。

Si_3N_4particles are used in composite plating with the characteristics of high hardness , good wear resistance and performance stability .

结果表明，PTFE的添加不仅可以提高PC的耐磨性，而且还可降低其摩擦系数；

Results show that the addition of PTFE can not only increase the wear resistance of PC , but also decrease its friction coefficient .

Sculpture和Bayer的耐磨性接近于牙釉质。

The wear resistance of Sculpture and Bayer is similar to that of enamel , and suitable for restoration .

在干摩擦磨损条件下，尤其在高载荷作用下，复合涂层的耐磨性明显高于普通Al2O3涂层。

Under the dry sliding wear condition , especially with high loading , the wear resistance of the composite coating is much higher than conventional Al2O3 coatings .

超音速电弧喷涂Ti-Al涂层耐磨性及工艺研究

Research on Wear-resistance of Ti-Al Coating Produced by Supersonic Arc Spraying