离合器片

用回归设计法进行离合器片摩擦特性的研究

A Study of Frictional Behavior of Clutch Disc by Regressive Design

安装顶部侧齿轮和离合器片组件。

Install the upper side gear and clutch disc pack .

通过在MM-1000试验机上的模拟试验及PC-1500计算机数据处理，并与离合器片零件试验结果对比，证明该新方法方便实用。

The results from analogue test on the MM-1000 test machine and data processing with PC-1500 computer were compared with results of clutch lining component tests . The new method is considered convenient and practical .

离合器片沿径向磨损规律及对测量的影响

Radial Wearing Principle of Clutch Disk and Its Influence on Measurement

变速箱离合器片冲齿模具的设计毛细管铝封片冲挤工艺及模具

Stamping-Extrusion Technology And Die Design of Aluminum Seal Sheet

离合器片在飞轮侧的表面撕裂、擦伤或磨损。

Facing on flywheel side of disc torn , gouged , or worn .

离合器片表面温度的测量与表面应力的计算

Measurement of Surface Temperature Distributions and Calculation of Surface Stresses on Clutch Discs

汽车离合器片配方的优化设计

Optimum Design for Automobile Clutch - Lining Formulations

离合器片模型试验新方法

A New Method for Clutch Lining Model Test

湿式摩擦离合器片翘曲变形研究

Friction Discs Distortion Phenomena in Wet Clutch

请注意离合器片上的标记。

Please note marking on clutch plate .

下部侧齿轮和离合器片组件

Lower side gear and clutch disc pack

螺旋离合制动机构在卷扬机上的应用用数学建模方法进行离合器片缠绕工艺的设计

Application of the Spiral Clutch Breaking Mechanism in Winch A Design for Spiral Wound Clutch Facing

该装置直接通过离合器片压力使起动平稳。

This system is charadterized by smooth starting through controlling the pressure of the clutch disk directly .

作者用测厚法与称重法进行的测量离合器片和刹车片磨损值的对比试验，证明称重法真实可靠。

Weight measurement method is proved reliable through contrast experiments of thickness measurement method and weight measurement method ot test the wear of clutch lining and brake lining .

含21%玻璃纤维的无石棉摩阻材料离合器片，其性能已符合国家标准，可以进行扩大生产。

Thus , a 21 % glass fiber non-asbestos friction material of clutch lining was prepared , its properties all meet the GB national standards and will be developed industrially .

作者在综述了离合器片模型试验现行的试验机和试验方法基础上，应用相似理论，确定模拟准则，提出了离合器片模型试验新方法。

Based on the review of model machines and test methods , applying the principle of similitude , the establishment of the analogue criterion . A new method for clutch lining model test is proposed .

本文介绍用回归设计法对离合器片摩擦特性进行的试验研究，并应用它定量分析了压力、速度、温度、转数对离合器片摩擦特性的影响。

A regressive design has been applied to the study of frictional characteristics of clutch disc and the quantitative analysis for the effects of load , velocity , temperature and rotating number on frictional behavior of clutch disc .

本文采用新的原材料和新技术，研制出具有很高耐热性和很低游离酚含量的S－155芳醇酚醛树脂，该树脂可作为高级轿车、摩托车刹车片和离合器片的基体树脂。

S 155 aromatic alcohol phenolic resin with high thermal resistance and low free phenol content are studied through using new raw material and new technology . This resin can be used for the matrix resin of high quality car , motorcycle brake block , clutch lining .

TBM离合器摩擦片失效成因及对策

The invalidation reasons and countermeasures of TBM clutch 's friction pieces

适用于TBM驱动离合器摩擦片的摩擦材料研究

Research on Friction Materials for TBM Driving Clutch Plate

TBM驱动离合器摩擦片失效分析及预防措施

Failure and Prevention of Friction Disc for TBM Clutch

磨损的离合器摩擦片磨片磨损对打浆生产使用效果的影响

Worn clutch facing The Effect of Disc Abrasion on Pulp Refining

摩托车湿式离合器摩擦片的研制

The R & D of Friction Lining of Motorcycle Wet Clutches

旋转强度是离合器衬片的一项重要的质量指标。

Rotation strength is one of important quality parameters of cluth linings .

主离合器摩擦片温度场的数值解法

Numerical Solution of Temperature Field of Main Clutch Friction Plate

离合器摩擦片非稳态温度场的计算

Numerical Investigation Determination Transient Temperature Field in Friction of Clutch

磨损的离合器摩擦片磨钢丝针用薄片砂轮

Worn clutch facing disc wheel for steel wire needle sharpening

汽车离合器摩擦片数量选择及其参数优化设计

The Parameter Optimal Design for Friction Disks of Automotive Clutch

离合器摩擦片长期磨损规律研究

A Study on the Wear-rules of the Friction Disk