模压

对聚合物光栅的衍射观察和测量，证明用模压技术制作的PC聚合物矩形光栅具有很好的衍射效率和表面质量。

By observing and measuring diffraction of the polymer grating , we prove that the PC polymer rectangle grating made in mould pressing technology has a higher diffraction efficiency and good surface quality .

电动机MCR耐高温铁粉型模压磁性槽楔

MCR Magnetic Wedge of Iron Powder Type with Mould Pressing and Resistant to High Temperature for Motors

它们可分为两类：可浇铸的和必须由挤压或模压加工的。

They can be divided into two classes , those which are castable and those which must be processed by extrusion or compression molding .

模压工艺对7075/SiCp复合材料组织和性能的影响

Effect of Die Forming Technologies on Microstructure and Properties of 7075 / SiC_p

热模压辅助先驱体浸渍裂解制备Cf/SiC复合材料研究

Fabrication of c_f / sic composites via precursor infiltration and pyrolysis assisted by hot-pressing

模压玻璃钢的X射线探伤

Nondestructive X-ray testing of compression moulded fiber reinforced plastics

模压重组木H型材的制造工艺

Technology for H-Shaped Moulded Reconstituted Timber Manufacture

PE泡沫绝缘料模压发泡工艺的考察

Study of Mould Pressure Foaming Technology for PE Insulating Foam

PE泡沫绝缘料模压发泡质量的影响因素研究

Study on influence on foaming quality of foam insulating PE in molding

Al2O3粉模压成型与烧结尺寸变化的研究

Study on size variation of al_2o_3 green during shaping in die and sintering

浸渍模压与CVD复合工艺制备质子交换膜燃料电池用炭纸

Carbon paper fabricated by molding and CVD process for PEMFC application

正交法对DEM技术中模压工艺的优化研究

Optimization for Hot Embossing Process Parameters in DEM Technique by Orthogonal Experiment

Armos/环氧FRP模压板耐库存和湿热性能的研究

Study on the Anti-aging and Hygrothermal Properties of Armos / epoxy Molded Plates

采用热模压法制备了环氧模塑料（EMC）。

The epoxy molding compounds ( EMC ) was prepared by hot pressing molding method .

设计了一种用于测量模压腔体内大荷载压强的光纤Bragg光栅（FBG）压强传感器。

Design a kind fiber Bragg grating ( FBG ) pressure sensor for measuring the large load pressure in mold chamber .

BMC模压制品的颜色均匀性与低收缩添加剂的相关性研究

Study of the relationship between the mottle of BMC parts and low profile additive

考察了接触压力、PF树脂含量及模压工艺条件对接触电阻的影响。

The influences of contacting pressure , PF content and compression molding parameters on the contact resistance were investigated .

他研究调制油墨的方法，使字模压上去时，油墨不致溅开。非平衡磁控溅射掺Cr类石墨镀层的结构分析

He learned to mix ink so it would not spread when pressed by the type . Analysis of Structure of Cr-doped GLC Coatings Deposited by Unbalanced Magnetron Sputtering

产品名称：玻璃纤维拉挤，RTM，模压，层压专用针刺毡。

Name of Product : Needled glass mat for pultrusion , RTM , molding , sandwich pressing .

通过模压的方法制备了聚四氟乙烯（PTFE）和纳米高岭土填充的聚苯硫醚（PPS）复合材料。

Polyphenylene sulfide ( PPS ) composites filled with Polytetrafluoroethylene ( PTFE ) and kaolin nanoparticles were prepared by compression molding .

为此，提出了一种新型的沥青基炭复合材料的制备工艺，即模压半炭化成型工艺（简称MSCT工艺）。

Therefore , this paper brought forward a new preparation technology , namely mould pressing and semi-carbonization technology ( MSCT ) .

以Si3N4粉末作为增强组分与环氧树脂进行复合，采用模压法制备了氮化硅/环氧树脂复合电子基板材料。

A kind of composite substrate was fabricated using Si_3N_4 powder as filler and epoxy as matrix and employing the method of press molding .

在成型温度180℃下，以碳布为增强体、ABS为基体，采用模压成型，生产出CB/ABS复合材料层压板。

In the molding temperature of180 ℃, CB as reinforcement , ABS as matrix , using hot molding press to produce CB / ABS composite material laminates .

随后采用模压法对增塑后的PET片材进行微发泡，研究了发泡温度、发泡压力和增塑剂含量等加工参数对微发泡增塑PET片材的泡孔结构和拉伸力学性能的影响。

Plasticized PET sheets were microcellular foamed by compression molding and the effects of foaming temperature , foaming pressure and plasticizer content on the cell structure and tensile mechanical properties were investigated .

用模压的方法制备了甲基丙烯酸缩水甘油酯（GMA）改性大豆分离蛋白质（SPI）塑料。

Glycidyl methacrylate ( GMA ) modified soy protein isolate ( SPI ) plastics were prepared via the compression molding .

以热塑性酚醛树脂（PF树脂）、天然鳞片石墨（NG）为主要原料，采用模压工艺制备了NG/PF复合双极板。

Thermoplastic phenol formaldehyde resin ( PF ) and natural crystalline flake graphite ( NG ) were chosen for composite bipolar plates by compression molding .

GMT材料流动成型后玻纤在平面内发生取向，导致模压件呈各向异性。

The planar orientation of fibers may occur after the flow molding of GMT , which can result in anisotropy molded parts .

塑料矩形光栅可以在波分复用（WDM）系统中作为复用/解复用器，制作塑料矩形光栅最简单可行的方法是采用模压技术。

The rectangle plastic gratings are widely used for multiplexing / demultiplexing in the WDM system . The most simple and feasible means is to adopt the mould pressing technology .

基于Laplace传热理论，建立了模压成形模具的三维稳态仿真模型以及制品的一维瞬态仿真模型。

The three dimensional steady numerical simulation model of the mold and the one-dimensional transient simulation model of the nonwoven composite part were built up based on Laplace theory .

TiH2粉末模压成形剂优化研究

Research on the binder for TiH_2 powder die pressing