最高温度

最高温度11摄氏度，即52华氏度。

Highest temperatures 11 º Celsius , that 's 52 º Fahrenheit .

气象预报伦敦周末天气晴热，最高温度为摄氏32度，最低温度为摄氏22度。

Hot and sunny weather is forecast for London over the weekend with about high of32 ℃ and low of22 ℃ .

七月份最高温度可能达到36摄氏度。

The maximum temperature in July may be 36 degrees Celsius .

OPGW允许的最高温度

Permitted highest temperature of OPGW

预混燃烧效率高并且便于控制火焰最高温度从而有效地抑制NOx，因此在先进燃烧器中被广泛应用。

Premixed combustion is of high efficiency and it provides the convenience for controlling the maximum temperature of flames and then effectively suppressing NO_X . Thus it is widely used in advanced combustors .

但是，目前铁电薄膜的制备工艺一般要经过600℃以上的热处理，然而硅MOS器件所能承受的最高温度为450℃。

However the fabrication craft to PZT ferroelectric thin films must generally be processed above 600 ℃, while the accomplished silicon integrated circuit can only withstand 450 ℃ .

用ANSYS有限元分析软件计算了某型负重轮橡胶轮缘的温度场，定量分析了5个参数对轮缘最高温度的影响。

The temperature field of a kind of road wheel 's rubber flange was calculated with finite element analysis software ANSYS , and the effect of five parameters on the highest temperature of wheel flange was analyzed .

结果表明，最高温度在95°E以西及黄河以北地区普遍呈增温趋势，而在东部黄河以南却呈降温趋势；

The results show that increasing trends of maximum temperature are in the areas west to 95 ° E , and north to the Yellow River , however , decreasing trends were observed in eastern China south to the Yellow river .

基于镍氢电池性能实验结果，分析了轻度HEV用镍氢电池在不同SOC情况下不同充电电流的最高温度、温差变化趋势。

Based on the result of NiMH battery performance experiments , changing trend of maximal temperature and difference in temperature of HEV NiMH battery in different SOC and different charging current is analyzed .

在同一块PCB上，将生热率高的器件置于板面四角，而其余的分布于其间，可有效地均匀热场并使最高温度显著降低。

The thermal field would be well distributed and the highest temperature be cut down evidently , if electronic components with higher heat generation rate be sit in four corners of the PCB while the else among them .

PTT纤维属易染型纤维，在最高温度染保持30～40min即可。

PTT fiber is a kind of easy dyeing fiber and dyeing time is 30 ~ 40 mins at the highest dyeing temperature .

当考虑微尺度效应时，层板最高温度高于忽略此效应的温度，且随着Kn的增大，二者的差别也随之增大。

If the micro scale effect is considered , the highest temperature of platelet is higher than it is neglected , and as Kn increases , the discrepancy gets larger .

在从1.03s到17.1s的时间内温度场最高温度仅仅上升了167℃。

From 10.05s to 17.1s the temperature only raises 167 ℃ .

本文使用已有软件计算出托砖架最高温度点温度，对一个自适应神经模糊系统（ANFIS）进行训练，然后对未知数据进行预测，取得了准确的结果。

The highest temperature of the ring got by ready - made software is used to train an ANFIS , then the ANFIS is used to predict unknown data , and exact results are got .

根据前若干天的温度敏感分量值、温度信息（包括平均温度、最高温度和最低温度）以及预测日的温度信息，采用BP网络构成的负荷预测器，得出预测日的温度敏感分量的预测值。

The latter is obtained by a BP network whose inputs are history information of load , temperature ( including the averaged temperature , the highest temperature and the lowest temperature ) and the temperature of the predict day . The varying component is forecasted by Wavelet-Kalman filter based method .

而如果能够将预混合燃烧过程缸内的局部最高温度控制在热NOx开始生成的温度1800K以下，就能够同时实现较低的PM和NOx排放。

In addition , the maximum combustion temperature should be less than 1800K , the critical temperature for thermal NO_X formation , then the PM and NO_X emissions could be simultaneously reduced greatly . The paper also presents a combustion process control strategy mode .

预浸温度为80℃，时间10min，蒸煮最高温度为168℃，保温时间60min，粗浆得率45.5%，卡伯值26.6，白度21.1%ISO，所制取的红麻浆具有较高的成浆强度。

The pulp yield is 45.5 % , kappa number is 26.6 and the brightness is 21.1 % ISO . The results showed that the pulp has good strength properties .

结果表明，第一壁铍保护板和RAFM钢的最高温度符合热工安全设计要求。

The results show that the maximum temperature of beryllium armor and RAFM steel of first-wall meet the thermal design requirements .

250MW负荷水平下的最高温度比200MW负荷水平下的最高温度高约80K；

The maximum temperature in the section under load of 250 MW is about 80 K higher than that under load of 200 MW .

概述了电缆短时容许最高温度限值的有关试验分析、国外标准和短时应急过载能力的IEC、日本标准算法及其应用意义。

The paper describes tests and analysis on permissible maximum temperature limit for cable short time overload , introduces international standards , IEC standard for emergency overload and Japanese standard algorithm and its application . scavenging ability of BSCA were measured by the chemical simulation .

结果表明，刀具的最大Mises应力位于刀具前刀面靠近切削刃的区域，最高温度出现在切屑与前刀面的接触区域。

The simulation results showed that the maximum Mises stress was obtained in the area of the tool rake face near the cutting edge . The maximum temperature was found in the contact area of the chip and the rake face .

试验表明，烘烤的钢包内衬温度达到了1200℃，罐底最高温度可达1350℃，冷罐烘烤时间为4h，400～800℃热罐烘烤时间为2h。

It is shown through tests that the lining temperature of dried ladle reaches to 1200 ℃, and bottom temperature 1350 ℃, drying time of cold ladle is 4 hours , the drying time of hot ladle with 400 ~ 600 ℃ 2 hours .

该文还以某榴弹炮的M14开槽管状装药为例，计算得其膛壁最高温度为1284K，单发磨损为17.9μm。

As an example , the maximum wall temperature of 203 mm howitzer using M14 slotted stick propellant is 1284 K , the heat wear in single shot is 17 9 μ m.

研究表明：麦草KP法一级深度脱木素蒸煮适宜工艺条件为：用碱量14%（Na2O计），硫化度15%，助剂用量0.3%，蒸煮最高温度140℃，保温时间120min，液比1∶5。

The compatible conditions for the one stage extended delignification of Kraft pulping of wheat straw were : total alkali charge 14 % , sulfidity 15 % , liquor-to-wood ratio 1:5 , maximum temperature 140 ℃, time at cooking temperature 120 minutes , additive charge 0.3 % .

结果表明，牛粪与玉米秸秆以4∶6配比效果最好，堆肥升温快，3d达到50℃，高温维持时间为16d，最高温度达71℃，堆肥29d后，白菜种子发芽指数高达81.6%；

The results indicated that 4 ∶ 6 of dairy manures and corn stalks was best ratio . Its temperature rose rapidly to 50 ℃ on the third day , and high temperature maintained for 16 days . Maximum temperature was 71 ℃ .

流动相含10%正丙醇时，萘普生对映体和布洛芬对映体达到完全分离应控制的最高温度分别为298和288K。

When naproxen and ibuprofen enantiomers were entirely separated by the mobile phase containing 1.0 % 1-propanol , the maximum temperatures allowed were 298 K and 288 K , respectively .

试验表明：中小型柴油机（1100A、495Q）在工作过程中活塞环&缸套摩擦副摩擦面的最高温度（不是微凸体的闪点温度）接近220℃。

Experiments show that the maximum temperature at f r ic - tional surfaces of piston ring-cylinder liner during practical work ( no flash temperature of asperity ) is close to 220 ℃ .

试验期为54d，期间猪舍内最高温度39℃，最低22℃，平均相对湿度为71.6%。

The test period is 54 days , during which , the highest temperature in pigsties is 39 ℃, the lowest is 22 ℃, and the mean relative humidity is 71.6 % .

并对蚕茧丝质的影响比较分析表明，春蚕期上蔟28h出现38.2℃的最高温度，夏蚕期在上蔟后32h出现38.7℃的最高温度。缩短春蚕期幼虫全龄经过的方法

The results indicated that the highest temp . , 38.2 ℃, appeared in 32h in spring , and 38.7 ℃ in summer after cocooning . Research on Methods for Decreasing the Duration of Whole Larva Instar During the Period of Spring Silkworm

试验结果表明，熔料可达到的最高温度不低于2500K；坩埚的铜质对熔锭并无污染；

The results indicate that the maximum temperature of the molten alloys is not lower than 2500K , the copper of the crucible does not enter into the ingots of alloys , and the ingots are very homogeneous .