揉切

  • 网络rolling;rolling and cutting
揉切揉切
  1. C揉切机切碎。真空式密封件切唇修边机的研制

    Study on Machine for Cutting Seal Ring 's Lip and Edge

  2. C揉切机切碎。棉秆切碎及压缩成型的试验研究

    Experimental Studies on Chopping Cotton Stalk and Briquetting Process

  3. 再次,本文运用UG建立了9LRZ-80型秸秆揉切机约二百个零、部件的三维实体模型,并将各零件虚拟装配,对关键部件切碎器进行动态仿真、动态分析,同时进行间隙检查。

    Thirdly , parts of two hundred were drawn , virtual assembled by UG . Then the cutter was gone on dynamic simulations , dynamic analysis , and the gap test .

  4. 玉米揉切压捆青贮机关键部件的设计

    Design of Key Parts of Corn Stalk Rubbing & Cutting Baler

  5. 茶叶揉切机齿辊节距误差数理统计建模与分析

    Statistics Modeling and Analysis on Pitch Errors Of Black Tea CTC Rolls

  6. 秸秆揉切机用刀片磨损的研究

    Study on Cutter Wear of a Rubbing and Cutting Machine

  7. 红碎茶揉切压力测试与分析

    Measurement and Analysis of Rolling-Cutting Pressure for Broken Black Tea

  8. 揉切后玉米秸秆的压缩试验研究

    Study on Compression Experiment of the Maize Straw after Being Rubbed and Cut

  9. 揉切机试验结果表明,影响试验指标的主要因素是搓板的结构型式。

    The primary factor influencing the test quotas is the construction of the vane .

  10. 玉米秸杆揉切特性及其虚拟仪器测试系统的研究

    Study on Cutting and Rubbing Properties of Corn Stalk and Its Test System of Virtual Instrumentation

  11. 红茶除了要萎凋、揉切、加热外,在最后一道加热工序前还需要进行发酵。

    In addition to the leaves being withered , rolled and heated , black tea leaves are fermented before the final heating process .

  12. 本文以自行设计的压缩装置为实验设备,进行了闭式压缩试验研究,试验发现揉切后玉米秸秆在闭式容器内的压缩过程可分为松散、过渡和压紧3个阶段。

    The results are as following : The compression course of the maize straw in the closing type container can be divided into the loose , transition and compressing tightly 3 stages .

  13. 结果表明,结构改进显著提高了刀片的耐用性能,降低了单位生产量的刀片材料损耗,提高了揉切机的生产率,加工质量也得到相应改善。

    Results show that the life of cutters was extended , and blade materials wastage was reduced , and productivity of the rubbing and cutting machine was increased , process quality was improve .

  14. 新型秸秆揉切机能扩大饲料来源,改善秸秆品质,避免粗饲料茎杆部分不被采食的浪费。

    By a new9LRZ-80 rubbing and cutting machine used , the range of feedstuff was enlarged , the quality of straw-stalk was improved , as a result , the waste of coarse fodder of straw-stalk was decreased .

  15. 秸秆切割破碎与揉切机刀片耐用性试验研究刀尖是刀具中最薄弱的环节,提高刀尖及切削刃的强韧性对改善刀具切削性能尤其重要。

    Experimental Study on Straw Cutting Process and Wear Resistance and Strength Toughness of Cutters ; So improvements of the obdurability of the tool tips and cutting edges are very important to better the cutting property of the end mill .