弯曲强度

合金的弯曲强度和弯曲模量都随着合金中ABS用量的升高而下降。

The flexural strength and flexural modulus decreased with the increasing amount of ABS .

UG环境下齿轮弯曲强度的有限元仿真

Finite element analysis of gear flexural strength under UG background

在相同温差热震后的试样剩余弯曲强度随着材料中Cu含量的增加而增大。

The thermal shock resistance property increases with increasing of Cu content .

Al2O3/TiC复合陶瓷高温弯曲强度与弯曲切口强度研究

High temperature notch flexure strength and its probability distribution of Al2O3 / tic ceramics

结构陶瓷弯曲强度的Weibull统计实验研究

Research of Weibull statistics on the bending strength of structural ceramics

力学性能显示，加入HA微粒后，弯曲强度和弯曲模量均得到了提高。

Mechanical property showed that bend intensity and bend mould were both enhanced after addition of HA granules .

石英陶瓷弯曲强度的Weibull统计分析

Weibull Statistical Analysis of Bending Strength of Quartz Ceramic

研究了不同炭涂层、高温热处理对C/CSiC复合材料弯曲强度和断裂方式的影响。

The effects of different carbon coatings and high temperature treatment on the flexural strength and fracture modes of C / C-SiC composites were studied .

结果表明，在210C、1h回火条件下，钢锯条具有最佳静弯曲强度及挠度。

Results show that the steel saw blade by tempering at 210 ℃, 1 hour has optimum bending strength and deflection .

随着AE用量的增加，固化物冲击强度和弯曲强度都逐渐提高，热变形温度却逐渐减小。

As adding the content of AE , flexural strength and impact strength of cured resin increase gradually , but HDT decreases .

将经碳纤维预浸织布加强的PMMA与对照组相比较，弯曲强度显著增加（P＜0.01），其强度满足临床需要。

Comparing the PMMA which had strengthened by pre-submerged carbon fabric weaved cloth with the comparing group the flexure strength and both added obviously , the quantity satisfy the clinic requests .

用SEM和TEM观察了材料的显微结构，指出弯曲强度增加是由于荷载从基体转移到晶须。

The microstructure examined by SEM and TEM indicates that the increase in bending strength is found to be dependent on the load shift from matrix to the whisker .

研究结果表明：将PA6、PP和PP-g-MAH共混解决了PA6干态下的冲击强度低，吸水率大的问题，但拉伸强度、弯曲强度等力学性能较PA6有所下降。

The results showed that although addition of PP and PP-g-MAH improve impact behavior and lowers absorption , but the mechanical properties decrease .

通过测试，发现PP接枝物的加入提高了带材的弯曲强度，表明PP-g-MAH提高了相界面的作用力。

It is found that because of adding PPg-MAH , the blending strength of tapes is enhanced and the interface compatibility is improved .

复合材料具有较优异的力学性能，随着SiC颗粒尺寸减小，复合材料的硬度、三点弯曲强度和弹性模量逐渐增加。

The mechanical properties of composites are superior . With the decreasing of the SiC particles size , the hardness , three-point bending strength and elastic modulus increase step by step .

随着复合材料中HA含量的增加，材料的弯曲强度、弯曲模量有大幅提高，而材料的抗拉强度即韧性降低不大。

With the increase in HA content , the flexural strength and flexure modulus of composites had been greatly increased and the tensile strength of composites had only a little change .

当烧结助剂为含量为10%时，材料弯曲强度最高。（2）随着烧结温度的增加，Cf/SiC制动材料的弯曲强度先增大后减小。

When the sintering aids content is 10 % , the bending strength is the highest . ( 2 ) With the increase of sintering temperature , the bending strength of C_f / SiC brake materials first rise and then fall .

M-HOS晶须能提高PP的拉伸强度、弹性模量和弯曲强度、弯曲模量；

The tensile strength , flexible modulus , bending strength and bending modulus of PP were significantly enhanced by M-HOS Whisker .

该产品生产工艺简单，适应性强，与普通PP树脂相比，其弯曲强度、弯曲模量和热变形温度可显著提高，制品的收缩率和翘曲率明显降低。

Comparing with PP resins , these two composites had much higher flexural strength , flexural modulus , heat deformation temperature , better aging properties and lower shrinkage the processing technologies were simple .

结论：芳纶纤维能提高PMMA基托的弯曲强度和冲击强度。

Conclusion : By incorporating aramid fibers into the PMMA denture base resin , the bend strength and impact strength of the denture base resin can be improved .

碳纤维增强HA环氧复合材料的冲击韧性高于碳纤维增强环氧复合材料，而弯曲强度和弯曲模量低于碳纤维增强环氧复合材料。

The impact toughness of the carbon fiber reinforced HA / epoxy composite was higher while the flexural strength and modulus were lower than the corresponding values of carbon fiber reinforced epoxy composite .

同时，血清HYP含量升高，骨骼弯曲强度降低。

Meanwhile , the flexional strength of bone diminished , while the content of sera hydroxyproline ( HYP ) increased .

结果化学固化PMMA组的弯曲强度为（51383±2761）MPa，弹性模量为（17912±113760）MPa。

Results The flexural strength of chemical-cured PMMA group was ( 51 383 ± 2 761 ) MPa , the flexural modulus was ( 179 1 2 ± 113 760 ) MPa ;

添加增塑剂TBC后，聚乳酸的拉伸强度降低，弯曲强度和冲击强度提高。

With the increase of TBC content , the tensile strength decreased , but the flexural strength and impact strength increased .

在EP中加入5%纳米粘土，制得的纳米粘土/EP复合材料的抗冲击强度和弯曲强度，分别比纯EP提高303.2%和45.5%。

When accede to 5 % nano-clay in EP , that impact strength and distort strength of the nano-clay / epoxy composite materials were improved 303.2 % and 45.5 % .

结果表明，OMMT的添加可以提高体系的拉伸强度、弯曲强度和弯曲模量，但冲击强度会有某种程度的下降；

The addition of OMMT improved the tensile strength , flexural strength and flexural modulus of the alloy , however , the impact strength decreased to a certain extent .

接头弯曲强度随连接时间的增加、即Si3N4／TiN界面的连续和致密化而显著提高。

Four point bending strength increased with the increase of bonding time , or with the continuation and the compactness of the Si 3N 4 / TiN interface .

TiC陶瓷骨架相对密度为72%的TiC/Cu复合材料的弯曲强度达到955MPa，较热压纯TiC陶瓷材料有大幅度的提高。

The bending strength is 955 MPa when the relative density of TiC skeleton is 72 % . TiC / Cu ceramic-metal composite can be used as a light ablation resistance material .

目的：利用弯曲强度和Weibull分析方法对可被CAD/CAM技术加工的渗透陶瓷的结构可靠性进行分析，为临床选择应用该陶瓷材料提供依据。

PURPOSE : To explore the structural reliability of machined infiltrated ceramic made from ultrafine alumina powder for dental CAD / CAM by means of flexural strength together with Weibull analysis .

本文采用拉挤成型工艺制备GFRP棒材，并测量了其在不同条件下的抗拉强度和弯曲强度。

In the paper , GFRP bar was fabricated by the technology of drawing and squeezing , and its tensile strength and bending strength under different conditions were measured .