喷油

另外我厂一些型号的喷油泵支架目前还无法生产。

Some type of oil spout pump bracket can not be produced in our factory now .

公司目前拥有CNC数控机床、EDM火花机、铣床、注塑机、喷油无尘车间等各种先进生产设备。

At present the Company holds CNC numerical control machine tool , EDM spark machine , milling machine , injection machine , and oil injection non-dust workshop and other advanced manufacture equipments .

油箱在大量喷油。

The tanker was gushing oil .

P系列双弹簧喷油器的开发

Development of P Type Dual-spring Injector

并介绍了采用有限元法对新型小尺寸P系列轴针式喷油嘴结构进行的分析计算。

Analysis and calculation to structure of new small size P-type pintle injection nozzle was introduced .

基于MATLAB的柴油机高压喷油过程的模拟计算

Simulating Calculation of High Pressure Injection Process of Diesel Engine Based On MATLAB

AD型喷油泵燃油喷射系统计算机建模和仿真分析研究

Modeling and Simulation on Fuel Injection System of AD Type Pump by Computer

PE喷油装置在4缸柴油机上的应用

Application of PE Fuel Injection Device on Four-cylinder Engine

康明斯柴油机PT喷油器的维护和调整

Maintenance and Adjustment of PT Oil Injector in Cummins Diesel Engines

康明斯发动机PT喷油器试验及试验台的研制

Study on Cummins Engine Pt injector test and test stand

PT燃油系喷油器流量试验台的改进方案

The Improvement Scheme of the Flow Rate Test Stand for PT Injectors

PT型泵&喷油器调整新方法

The New Way Adjusting the PT Pump-injector

本文应用Fluent软件对喷油螺杆式空气压缩机第一级油气分离器内的气液两相流流场进行了数值模拟。

The flow field inside an oil-gas separator are simulated with software Fluent .

以发动机外特性试验数据为基础，建立了理论模型，获得了喷油脉宽、充气效率初始MAP。

According to the external characteristic and theoretical model builded , initial control MAPs for injection pulse width and volume efficiency were obtained .

PA6可变喷射正时喷油泵的优化设计

Optimization Design of PA6-Diesel Injection Pump with Variable Injection Timing

在位置控制的基础上，对电控喷油系统中的电控调速系统进行了控制研究，并结合实际情况采用了模糊和分段PID复合控制算法。

On the base of position control system , electronic governing system was investigated . A fuzzy PID compound control algorithm is proposed .

喷油嘴参数对TR燃烧系统排放性能的影响

Effects of Nozzle Parameters on Emission Performance of TR Combustion System

试验结果表明较大的A、B量孔尺寸差值和高的共轨压力，可以获得较好的喷油器开启响应特性。

The test result shows that by using bigger dimension difference of control hole A and B and high common-rail pressure the better open response of injector can be achieved .

基于电控喷油定时与EGR率实现柴油机HCCI/常规燃烧双模式的试验研究

Diesel Engine HCCI / Conventional Combustion Dual-mode Based on Electronic-controlled Injection Timing and EGR Ratio

根据正交试验法，制定了喷油器控制腔偶件的加工方案，并就控制A、B量孔尺寸对液力响应的影响进行了试验研究。

The machining project of control cavity was set down based on the orthogonal test method , and the influence of control hole A and B on the hydraulic response of injector was tested .

λSS法为可控喷油形成准均质稀混合气的优化控制策略开辟了一条新的技术途径。

λ SS set up a new technique approach which gives a new controlled strategy for optimizing the formation quasi-homogenous mixture .

日野KL系列发动机柱塞式喷油泵使用和维护简介

Operation , Maintenance & Repair for Plunger-Type Fuel Pump of HINO 's KL Series Diesels

具体分析了通过优化喷油延迟角MAP图来实现共轨蓄压式电控喷油系统喷油正时精确控制的方法。

The method of precious control of fuel injection timing of the common rail pressure-accumulating electronic control fuel injection system realized by optimizing MAP graph of fuel injection delay angle is analyzed in detail .

由于喷油持续期延长，低喷油压力使PAHs在生成后期生成速度加快。

Under the lower fuel injection pressure , the fuel injection duration was so longer that PAHs formation became faster at later period .

结果表明：延后喷油正时和（或）减少压缩比可以实现柴油机的低温燃烧，从而降低柴油机的NOx排放率，但柴油机的油耗率和烟度将受到影响；

Experiment results make it clear achieving low temperature combustion and reducing NOx emission from the diesel engine by reducing injection timing or / and compression ratio , but increasing fuel com-sumption and smoke ;

并且，对冷EGR和喷油延迟这两种降低柴油机NOx排放措施进行比较。

Meanwhile , cooled EGR and the fuel injection timing delay are compared in respect of the effect of decreasing NOX emission from diesel engine .

结合发动机空燃比的控制特征，研究了一种能自适应补偿喷油量的CMAC控制器。

Combined with control characteristics of engine air fuel ratio , the CMAC controller which is self adaptive to compensate fuel injection volume is studied .

对发动机喷油系统参数对二甲醚（DME）喷雾燃烧过程的影响进行了实验研究，包括喷孔直径和喷油提前角对喷雾燃烧过程的影响。

The influence of injection parameters including the nozzle diameter and injection timing on the spray and combustion process of dimethyl ether ( DME ) was investigated .

为了缩短柱塞式燃油喷射系统产品研制开发周期，提出了引入修正系数的AD型喷油泵系统喷射过程理论模型计算机建模的研究方法。

In order to reduce some experiments and cut down the consumption of raw materials needed for modeling of fuel injection process , a theoretical method based on modeling by computer is proposed for research on AD pump fuel injection system .

GD-1燃油喷射系统喷油参数对发动机性能的影响

Influence of Injection Parameters on the Performance of a DI Diesel Engine with GD-1 Fuel Injection System