rearward

The centre of pressure moves rearward and the aeroplane becomes unbalanced .

气压中心后移使飞机失去平衡。

Move the seat to its fully rearward position , if possible .

如果可能，将座位移动至其最靠后的位置。

Numerical Simulation of Turbulent Flow Flow Over a Tiny Rearward facing Step on Circular Cylinder

圆柱面上微小后向台阶紊流绕流场的数值分析

A Case Study on Severe Local Heavy Rain over the Rearward of a Landed Typhoon

登陆台风后部局域强降水的个例分析

Fit rearward facing baby seats in the rear of the car .

适合后向婴儿座椅在汽车的后部。

Wind Tunnel Tests of Bound Submissiles Ejected Rearward Into Base Flow Field

子弹束后向抛入底部流场的风洞试验

Do not want the dispute of rearward comment boss .

不要在背后议论老板的是非。

Mechanism simulation of retractable rearward fin stabilizers with Pro / ENGINEER

用Pro/ENGINEER进行后收式减摇鳍执行机构的机构运动分析

The Calculation of Incompressible Laminar Flow Over a Swept Rearward & Facing Step Using The Finite Element Method

用有限元法计算绕后掠的后台阶的不可压层流流动

Move glass carriage to vent position and remove rearward adjustment bolt from adjustment bracket .

将玻璃搬运车移至通风口位置，并从调节支架上拆卸后调节螺栓。

Remove the starter rearward from the engine , rotating the starter as necessary .

从发动机向后拆下起动机，必要时转动起动机。

( especially of aircraft wings ) angled rearward from the point of attachment .

（尤指飞机机翼）从连接点向后转变角度。

Push tank rearward into the holder and engage the electrical plug connection for the fluid level indicator .

将液箱向后推入支座，并装上液位指示器的电气插头。

Landscape Rearward The World

世界背后的风景

He moved back ; tripped when he stepped backward ; she looked rearward out the window of the car .

他向后移动；他在向后走的时候被绊倒了；她向汽车后车窗看去。

The cylinder pushing rearward leverage balancing lifting mechanism was selected as suitable to light dump truck through comparison of lifting mechanism structures .

通过对举升机构的结构型式的比较，选出了适合于轻型自卸汽车的举升机构&液压缸后推杠杆平衡式举升机构。

A six-way power seat includes up , down , forward , back , tilt forward , and tilt rearward seat movement .

一个六向的电动座椅可以向上、下、前、后、前倾和后倾六个方向移动。

The distribution width of pressure and film profile is increased , secondary pressure peak and minimum film thickness shift rearward in the case of considering plastic factor .

此外塑性变形因素的存在使得接触区的压力和油膜分布宽度增加，第二压力峰和最小膜厚点后移。

In contrast , the warm rain process is characterized by short life period , more pronounced rearward tilt structure and extension of stratiform cloud .

相比之下，暖雨过程中飑线的生命周期缩短，而系统倾斜结构更明显，层状云区的发展比较旺盛。

When Lorentz force is small , the separation points on the cylinder surface will be moved rearward , but it cannot be suppressed completely .

Lorentz力较小时，流动分离点后移，但不能完全抑制流体的分离。

His coat , when he wore one , hung nearly to his heels and had the rearward buttons far down the back ;

他要是穿着上装的话，那上装就差不多拖到他的脚后跟，背后的两排并齐的扣子一直扣到屁股；

Abnormal rearward curvature of the spine , resulting in protuberance of the upper back ; hunchback . overhead cam shaft

脊柱后凸，驼背脊椎不正常地向后弯曲，导致背部上方凸出；驼背上凸轮轴上部凸轮轴

Make a breakaway from * The rein back is a rearward diagonal movement with a two beat rhythm but without a moment of suspension .

后退是以斜对角步伐做出向后退的两节拍动作，但是没有腾空期。

Drive to the front axle in high range is now engaged by pressing down on a one lever while low range is selected by pulling another lever rearward .

在高范围中的前轴现在被放下来，与一根杠杆相连接，而从低范围中选择的另一个杠杆向后拉。

Furthermore , the configuration of zygomatic body was observed on coronal sectional image . Results The average rearward slope angle of zygomatic-body was 80.03 ° .

在冠状位截面影像上观察颧骨的形态并测量上颌牙槽嵴最颊侧点到上颌窦最外侧点的水平距离。结果颧骨的前后倾斜角度平均为80.03°，即颧骨前倾9.97°；

The nose unit is twin-wheeled and retracts rearward .

前鼻下单元双轮并且向后收起。

70 vertebrae rearward and appendages were involved . The paravertebral soft tissue masses presented in 17 cases , the spinal cord were compressed in 10 cases .

70个转移椎体后部及附件受累，17例椎旁有软组织肿块，10例脊髓受压。

CASE REPORT The first case is subcutaneous swelling at right angle of mandible , the second case at the rearward of cervix and fine needle aspiration were performed in them .

[病例报告]给例1右下颌角处皮下肿物、例2后颈部皮下肿物均做了穿吸细胞学检查。

As you can see , some experimentation was done with a " swirl-induction " system and another conical front-section with rearward facing intake tubes .

正如你所看到的，一些试验做的目的是“涡流感应系统”，另一个锥形前与后方面临的摄入管节。

Starting at the forward end of the upper molding , force the molding onto the door panel flange and continue rearward until it is completely seated on the flange .

从上部嵌条的前末端开始，用力使嵌条到车门饰板上并且继续向后直到它完全固定在凸缘上。