lugs
- v.使劲拉;用力拖;吃力地搬运
- n.手柄;把手;耳朵;把柄
- lug的第三人称单数和复数
-
In this department , hydro-set plates are assembled and joined together at the plate lugs .
在这个工段,组装脱水固化的极板并通过极板耳连在一起
-
In general , vessels shall be provided with two earth lugs .
一般情况下容器应有两个接地耳。
-
Thickness Effect on Stress Concentration Factors of Lugs under Axial Tension Loads
轴向拉伸载荷作用下耳片厚度对应力集中系数的影响
-
System to diagnose the fatigue damage status of the lugs based on artificial neural network
基于神经网络的耳片疲劳损伤状态分析系统
-
Strength analysis of lugs in any angle loading
任意角度受载的耳片强度分析
-
Pay attention to the position of the lugs when doing this .
进行此操作时,请记录凸耳的位置。
-
Suitable lugs shall be used at both ends .
两端均应使用适当的吊耳。
-
Expert System for Failure Diagnosing and Fatigue Evaluating about Damage of Lugs in Aircraft
飞机连接耳片故障诊断疲劳损伤评估专家系统
-
Finite element analysis on transverse trench lugs at end of continuously reinforced concrete pavement
连续配筋混凝土路面凸形地梁锚固有限元分析
-
Observe the two upper lugs when doing do .
进行此操作时,注意两个上凸耳。
-
The trend was cutters > upper leaf > lugs among different leaf positions ;
不同部位间差异呈现中部叶>上部叶>下部叶的趋势;
-
Retaining lugs of bearing shells must be pressed together .
轴瓦的定位凸台必须压在一起。
-
Prediction of fatigue life for tension bolts and lugs
受拉螺栓和耳片的疲劳寿命估算
-
Damage to plug connection lugs during door removal !
车门拆卸过程中会损坏插头凸耳!
-
A computational approach to the loads shared between the teeth of turbine lugs
涡轮盘榫齿载荷分配的一种计算方法
-
An analysis on effective factors to fatigue lives of pull rod linking lugs of tube shaped cases
筒形机匣连接凸耳疲劳寿命及其影响因素
-
The fixing lugs point to the oil pan .
定位凸台指向油底壳。
-
In this article , a strength analysis of single double lugs under axial tension loads is conducted .
本文对受轴向拉伸载荷作用下的单、双耳片进行了强度分析研究,并进行了归纳总结。
-
Press together until the lugs engage at the sides .
同时压入,直到四周的凸耳都接合。
-
Make sure that all lugs are engaged .
确保所有凸耳都已入位。
-
Lugs should not be used to adjust misalignment in piping .
凸耳不应该用来作为管道校准。
-
If lugs are not provided , slings should be used .
如果没有凸耳,则应该采用吊索。
-
The stack shall be equipped with lifting lugs for mounting .
烟囱应配备安装吊耳。
-
FEATURES : - All boxes complete with internal supporting plate and lugs for wall mounting .
所有的盒子内部都有金属板和固定在墙上的挂码。
-
These have two locking lugs to differentiate them and to avoid confusion .
使用两个锁止片进行区分,以避免混淆。
-
Do not bend locking lugs too much when doing this .
执行此操作时不要过于弯折锁止片。
-
You will see a mark on one of the support lugs on the bulb holder .
将在灯座其中一个支撑凸耳上看到标记。
-
Press locking lugs and pull off the plug-in coupling .
按下锁止片并拔掉插入式管接头。
-
At this point I 'm welding the lifting lugs onto the crucible .
在这一点上,我焊接坩埚解除耳。
-
Press and open the lugs of the cable retainer .
按下并打开电缆卡子的凸耳。